Floor Cleaning; Connection Of The Batteries To The Machine; Starting Of The Machine; Adjustment Of The Brushes Pressure - ADIATEK ruby 45 light Serie Emploi Et Entretien

GB
ATTENTION:
Use always low foam detergent. To avoid foam pres-
ence, before starting working operation, introduce
into the recovery tank a minimum quantity of anti-
foam product.
Never use pure acid.

FLOOR CLEANING

CONNECTION OF THE BATTERIES TO THE MA-
CHINE
Plug in the batteries connector (1) to the machine
connector (2), placed in the rear part of the machine.

STARTING OF THE MACHINE

1. Press the brushes motor switch (2).
2. The signal lamp of the battery charge level (1)
will come on. Check that it is in green colour. If the
red colour appears, it is necessary to proceed for the
batteries' recharge (see under "BATTERIES RECHARG-
ING").
3. Press the suction motor switch (3).
4. Acting upon the solution valve lever (6) adjust
the solution detergent quantity bringing the floor
uniformly wet, avoiding the leakage of detergent
from the splash guard. Always consider that the cor-
rect quantity of solution detergent depends on the
type of floor, dirtiness and machine speed.
Acting upon this lever, the indicator on the instru-
ment board of the open solution valve (4) will turn
on.
5. Acting upon the brushes base lifting pedal (8)
lower the brushes base.
6. Acting upon the squeegee lifting lever (7) lower
the squeegee.
7. Activating the levers (5) the brushes will start ro-
tating transferring to the machine a forward move-
ment. The squeegee will start drying the floor.
8. During the first meters check that the detergent
solution flow is appropriate and that the squeegee
adjustment guarantees a perfect drying action.

ADJUSTMENT OF THE BRUSHES PRESSURE

Through the register (1) placed on the internal part
of the front right wheel, it is possible to adjust the
brushes pressure on the cleaned surface.
By turning the wing nut clockwise the pressure in-
creases, rotating the wing nut counterclockwise, the
pressure decreases.
This device allows a more efficient cleaning action
also on very difficult and dirty surfaces.

OVERFLOW DEVICE

In order to avoid serious damages to the suction mo-
tor, the machine is equipped with a float that inter-
venes when the recovery tank is full, closing the suc-
tion hose and stopping the suction.
When this happens, it is necessary to empty the re-
covery tank.
1. Hold the exhaust hose placed in the front part of
the machine.
2. Take off the exhaust plug acting upon its lever
and empty the recovery tank into appropriate con-
tainers, according to the standard norms for the liq-
uid disposal.
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.

EMPTYING DETERGENT SOLUTION

To empty the detergent solution remained in the so-
lution tank:
19
1. Bring the machine to an appropriate place for
tanks draining.
2. Unscrew the solution tank cap (1).
3. Unscrew the exhaust plug (2).
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.

FORWARD MOVEMENT

The traction of these machines is given by the brush-
es that, working on an inclined axle, transmit to the
machine the forward movement.

STOP

Releasing the lever of the movement, brushes rota-
tion will end, stopping the machine movement.
ATTENTION:
Moving the machine backwards, make sure that the
squeegee is lifted.

ADJUSTMENT OF BRUSHES INCLINATION

Through the register (1) placed on the brushes base
group, it is possible to adjust the brushes inclination
increasing/decreasing the speed of the machine.
A label placed on the brushes base indicates the ad-
justment levels LOW/FAST.
STOP OF THE MACHINE
CLEANING OPERATION
Before executing any type of maintenance:
1. Close the solution valve lever (6) and check that
the indicator of open solution valve (4) on the in-
strument board turns off.
2. Lift the brushes base acting upon the pedal (8).
3. Lift the squeegee acting upon the lever (7).
4. Turn the brushes motor switch off (2).
5. Turn the suction motor switch off (3).
6. Bring the machine to an appropriate place for
tanks draining.
GB
AFTER