SPARKY P 282 Notice Originale page 9

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 21
WARNING: The planer is designed so that the
blades are correctly aligned if placed flush into the bar-
rel slots and tightened correctly. When inserting new
blades it is essential that they sit square in their slot,
that they are fully inserted and that the cutting edges
are absolutely level, i.e. parallel to the surface of the
rear base. Only when all these conditions are satisfied
should the clamping bolts be tightened. If the blades
protrude or are not square, they could hit the casing
with serious risk to the operator and others in the vicin-
ity. Blade must be positioned centrally on the barrel.
NOTE: Your planing surface will end up rough and un-
even unless the blades are set and secured properly.
The examples show proper and improper settings:
▪ Clean smooth cut: (Fig.3)
▪ Nicks in surface – as caused by the edge of one or
both blades not being parallel to the rear base line.
(Fig.4)
▪ Gouging at start – as caused by the edge of one or
both blades not protruding enough in relation to the
rear base line. (Fig.5)
▪ Gouging at end – as caused by the edge of one or
both blades protruding too far in relation to the rear
base line. (Fig.6)
NOTE:
(a) front base (movable shoe)
(b) rear base (stationary shoe)
WARNING: The two red painted Allen screws
are secured with adhesive, they must not be adjusted.
The position of these screws may be altered by the
manufacturer only!
SWITCHING ON AND OFF
WARNING: Before plugging the machine into
the power point always check that the trigger switch (5)
and lock-off button (6) work properly. Before switching
on ensure that the blade barrel is not in contact with any
surface.
1. Plug in the machine, push in the lock-off button (6) and
pull the trigger switch (5). (Fig.8)
2. To stop the tool, simply release the trigger switch (5).
3. In order to restart the machine, it is necessary to oper-
ate both the lock-off button (6) and the trigger switch
(5). This is an important safety feature that helps pre-
vent accidental operation of the planer. (Fig.9)
WARNING: Please note that that the planer
blades continue to spin for some time after switch-
ing off the planer. Wait until the motor has completely
stopped before setting down the tool to prevent dam-
age to the planer blades or the surface.
Original instructions
PLANING
1. Rest the front base (1) flat on the workpiece surface
without the blades making any contact with the work-
piece.
2. Switch on the tool and wait for the blades to reach full
speed.
3. Move the tool gently forward, applying pressure on the
tool.
4. Push the planer beyond the edge of the workpiece
without tilting it downwards.
5. The rate of planing and the depth of cut determine
the quality of the finish. For rough cutting, you can
increase the depth of cut, however to achieve a good
finish you will need to reduce the depth of cut and ad-
vance the tool more slowly.
NOTE: Planing is easier if you incline the workpiece
slightly away from you so that you plane "downhill".
WARNING: Moving the machine too fast may
cause a poor quality of cut and can damage the blades
or the motor. Moving the machine too slowly may burn
or mar the cut.
The proper feed rate will depend on the type of material
being cut and the depth of the cut.
Practice first on a scrap piece of material to gauge the
correct feed rate and the cut dimensions.
WARNING: Clamp the workpiece to the
bench.
CHAMFERING AND REBATING
1. To fit the rebate depth, select the desired value by the
rebate adjustment knob (2).
2. Loosen the wing nut of the parallel fence guide (12),
position the slide to the desired rebating width and re-
tighten the wing nut.
NOTE:
(Fig.10)
(A) Rebated edge
(B) Chamfered edge.
PARALLEL FENCE GUIDE
WARNING: Always ensure that the tool is
switched off and unplugged from the power supply
before making adjustments, installing or removing
blades.
1. To fit the parallel fence guide (12), remove the parallel
fence attachment knob (11) and slide the fence guide
onto the planer.
2. Replace the fence attachment knob (11) and tighten it
firmly.
3. Loosen the wing nut securing the fence slide, position
the slide to the desired rebating width and re-tighten
the wing nut.
4. If it is necessary to rebate to a precise width, plane
a scrap piece of wood, measure the rebate distance
and adjust the setting if necessary.
7
EN

Publicité

Table des Matières
loading

Table des Matières