Introduction; Device Description (Fig. 1−19); Scope Of Delivery; Proper Use - Parkside PBTS 370 A1 Consignes D'utilisation Et De Sécurité

2. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment and suc-
cess.
Note:
In accordance with the applicable product liability laws, the
manufacturer of this device assumes no liability for damage to
the device or caused by the device arising from:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs carried out by third parties, unauthorised specialists.
• Installing and replacing non-original spare parts,
• Application other than specified,
• Failure of the electrical system in the event of the electrical
regulations and VDE provisions 0100, DIN 13 / VDE0113
not being observed.
Please consider:
Read through the complete text in the operating manual before
installing and commissioning the device.
The operating manual is intended to help the user to become
familiar with the machine and take advantage of its application
possibilities in accordance with the recommendations.
The operating manual contains important information on how
to operate the product safely, professionally and economically.
This helps you to avoid danger, costly repairs, reduce down-
times and to increase reliability and service life of the machine
In addition to the safety instructions in this operating manual,
you must also observe the regulations applicable to the opera-
tion of the machine in your country.
Keep the operating manual package with the machine at all
times and store it in a plastic cover to protect it from dirt and
moisture. They must be read and carefully observed by all op-
erating personnel before starting the work.
The machine may only be used by personnel who have been
trained to use it and who have been instructed with respect to
the associated hazards. The required minimum age must be
observed.
In addition to the safety instructions and the separate regula-
tions of your country, the generally recognised technical rules
for operating machines of the same type must also be ob-
served.
We accept no liability for accidents or damage that occur due
to a failure to observe this manual and the safety instructions.
14 GB/IE
3. Device description (fig. 1−19)
1 Knurled screw for sanding belt adjustment
2 Support foot
3 Sanding belt tensioner
4 Sanding disc
5 On/off switch
6 Transverse stop
7 Sanding table
8 Locking screw for sanding table
9 Angle scale
10 Suction port
11 Base plate
12 Allen screw
13 Sanding belt
14 Stop rail
15 Bottom disc guard
16 Screw for bottom disc guard
17 Allen screw
18 Screw for sanding belt guard
19 Sanding belt guard
20 Holder tube

4. Scope of delivery

• 1 belt and disc sander
• 1 transverse stop
• 1 sanding table
• 1 sanding belt P80 (pre-assembled)
• 1 sanding disc P80 (pre-assembled)
• 1 Allen key
• 1 operating manual

5. Proper use

The purpose of the belt and disc sander is to sand all types of
wood, depending on the size of the machine.
The machine complies with the applicable EC machinery direc-
tive.
• The manufacturer's safety, operating and maintenance speci-
fications as well as the dimensions given in the technical data
must be observed.
• Relevant accident prevention regulations and other gener-
ally recognized safety and technical rules must also be ob-
served.
• The machine may only be used, maintained or repaired by
trained persons who are familiar with it and have been in-
formed of the dangers. Any liability of the manufacturer for
damages resulting from arbitrary changes to the machine is
excluded.
• The machine is intended for use only with original accesso-
ries and original tools from the manufacturer.
• Any use beyond this is improper use. The manufacturer is not
responsible for the resultant damages, the user bears this
risk alone.
Please observe that our equipment was not designed with the
intention of use for commercial or industrial purposes. We as-
sume no guarantee if the equipment is used in commercial or
industrial applications, or for equivalent work.