DAB ACTIVE DRIVER M/M 1.5 DUAL Instructions Pour L'installation Et La Maintenance page 30

When "F1" error condition occurs, the input must be N O T
system unlocks.
i1 = 0 2 : L a ck of water from ex t ernal float (N C )
IN 1 : not energ i z e d input
IN 1 : energ i z e d input
N o te In order to make the system lock and display "F1" error, the input must be N O T energ i z e d for at least
GB
1 sec.
When "F1" error condition occurs, the input must be energ i z e d for at least 30 secs before the system
unlocks.
5 . 1.3.11.2 I2: Input 2 setting function (active set- point selection: "SP" or "P1")
i2 = 0 0 : I n pu t is d i sa b l ed .
I n pu t sta t u s h a s a l w a y s set - point = SP, w h a t ev e r th e inpu t m o d e is.
i2 = 0 1: 2 - set - point sy s tem ( N O )
I N 2 : not energ i z e d inpu t
IN 2 : energ i z e d input
N o te In order to make the system work at P1 set- point conditions, the input must be energ i z e d
1 sec.
When the system is working at P1 set - point conditions, the input must be N O T energ i z e d for at least
30 secs before the system g o es back to SP set- point working conditions.
i2 = 0 2 : 2 - set - point system (N C )
IN 2 not energ i z e d input
IN 2 : energ i z e d input
N o te In order to make the system work at P1 set- point conditions, the input must be energ i z e d for at least
1 sec.
When the system is working at P1 set - point conditions, the input must be N O T energ i z e d for at least
30 secs before the system g o es back to SP set
5 . 1.3.11.3 I3: Input 3 setting function (g e neral system enabling )
i3 = 0 0 : Input is disabled.
中
The system remains always enabled and the possible pressures are only SP and P1 (see:
i2). "F3" never appears on the display.
i3 = 0 1 : General enabling (N O )
IN 3 : not energ i z e d input
energ i z e d for at least 30 secs before the
"F1" alarm on display and system block (lack of water
from ex t ernal float)
N o rmal operation
a c tiv e set - point = SP. In normal display mode "Go" or
"Sb" is displayed; provided that no anti- freez e / a nti- block
procedure is performing , the SP parameter value is
displayed in GS display mode.
active set- point = SP. In normal display mode "Go" or
"Sb" is displayed; provided that no anti- freez e / a nti- block
procedure is performing , the P1 parameter value is
displayed in GS display mode.
for at least
active set- point = P1. In normal display mode "Go" or
"Sb" is displayed; provided that no anti- freez e / a nti- block
procedure is performing , the P1 parameter value is
displayed in GS display mode.
active set- point = SP. In normal display mode "Go" or
"Sb" is displayed; provided that no anti- freez e / a nti- block
procedure is performing , the SP parameter value is
displayed in GS display mode.
- point working conditions.
The system is enabled, "GO" or "Sb" is displayed.
Instruction manual V 1.
IN 3 : e nerg i z e d input The system is disabled, "F3" is displayed.
i3 = 0 2 : General enable ( N C )
I N 3 : not energ i z e d inpu t The system is disabled, "F3" is displayed.
I N 3 : energ i z e d inpu t The system is enabled, "GO" or "Sb" is displayed.
i3 = 0 3 : General enabling , w i th bloc k s reset ( N O )
I t is the same as i3 = 0 1 , bu t eac h time the system sw i tc h es f r om the disabled to the enabled
state ( I N 3 f r om energ i z e d to not energ i z e d) all rec o verable bloc k s are c a nc e lled.
i3 = 0 4 : General enabling , w i th bloc k s reset ( N C )
I t is the same as i3 = 0 1 , bu t eac h time the system sw i tc h es f r om the disabled to the enabled
state ( I N 3 f r om not energ i z e d to energ i z e d) all rec o verable bloc k s are c a nc e lled.
i3 = 0 5 : B l oc k s R e set
E a c h time inpu t I N 3 passes f r om state
bloc k s are c a nc e lled
Table su m marising the c o nf i g u r ation of the dig i tal inpu t s I N 1 , I N 2 , I N 3
V a lu e
i1
I n pu t is ig n ored, I n pu t is ig n ored.
0 0
"F1" never appears S P is the only set - point
W a ter lac k f r om ex t ernal f l oat Set- point: SP or P 1 ,
0 1 c o nnec t ed to I N 1 ( N O ) depending on I N 2 ( N O )
W a ter lac k f r om ex t ernal f l oat Set- point: SP o r P 1
0 2 c o nnec t ed to I N 1 ( N C ) depending on I N 2 ( N C )
M i nimu m ex t ernal pressu r e
sw i tc h inpu t normally open
0 3
K i w a standards
M i nimu m ex t ernal pressu r e
sw i tc h inpu t normally c l osed
0 4
K i w a standards
0 5
Table 8 : I n pu t s setting
5 . 1.3.12 P 1 : Set - point s etting ( o nly w i th ex p ansion c a rd in)
W h en parameter i2 is set at a valu e other than z e ro, I N 2 is u s ed to selec t one of the tw o settable set
The f i rst is SP ( s ee sec t ion 5 . 1.1.1 ) and the sec o nd is P 1 .
5 . 1.3.13 O1, O2 : OU T 1 e OU T 2 ou t pu t s setting ( o nly w i th ex p ansion c a rd in) .
I n Table 9 f i nd the parameters to assoc i ate f u n c t ions to dig i tal ou t pu t s OU T 1 and OU T 2
A s soc i ating f u n c t ions to dig i tal ou t pu t s OU T 1 and OU T 2
P a rametro 0 0
o1 C o ntac t alw a ys C o ntac t alw a ys c l osed
open
o 2 C o ntac t alw a ys C o ntac t alw a ys c l osed
open
Instruction manual V 1. 2
2
N O T energ i z e d to state energ i z e d all rec o verable
P a rameter
i 2 i3
I n pu t is ig n ore d,
"F3" never appears
A c t ive D r iver system g e neral
enabling , depending on I N 3
( N O )
A c t ive D r iver system g e neral
enabling , depending on I N 3
( N C )
A c t ive D r iver system g e neral
enabling , depending on I N 3
( N O ) + R e c o verable bloc k s
reset
A c t ive D r iver system g e neral
enabling , depending on I N 3
( N C ) + R e c o verable bloc k s
reset
R e c o verable bloc k s reset
- points.
Given valu e
0 1 0 2 0 3
The c o ntac t c l oses if a The c o ntac t opens if
bloc k in g error oc c u r s a bloc k in g error
oc c u r s
The c o ntac t c l oses The c o ntac t opens
w h en the pu m p is w h en the pu m p is
w o rk i ng w o rk i ng
2 7
GB
中