Servicing The Drive; Changing The Drive V-Belt; Troubleshooting; Technical Data - Sabo John Deere 43-EL VARIO Livret D'entretien

Servicing the drive

– It is absolutely essential that the Bowden cable runs easily for switching on and off,
so that the control drive works perfectly.
– The Bowden traction mechanism has been set ready for operation at the works
and requires no adjustment.

Changing the drive V-belt

The drive V-belt must be replaced by a specialist workshop.

18 TROUBLESHOOTING

Fault Possible cause
No power supply.
If the motor does not
start 5 seconds after
the unit is started
Power cable damaged.
Cutting height has been
set too low (grass is too
high and blocks the
starting of the motor).
Too much grass waste in
the housing.
Extreme vibration
Drive control bracket not
Mower will not move
pulled.
forward
Drive speed cannot be
regulated
Cutting blade blunt.
Cut not clean,
lawn turns yellow
Cutting height too low.
Mowing speed too high.
Insufficient overlap
between mowing lanes.
Lawn matted.
Turbo signal ignored
Ejector blocked
J + K .
Cutting height too low
with grass too high.
Mowing speed too high.
Grass is damp.
Cutting blade blunt.
The mulched grass
does not look good:
clumps, excessive cut
material, coarse cut
Mulching rule ignored
(cut max. 1/3 of grass
height; the grass height
to be cut must be less
than 10 cm)
Driving speed too high.
Grass accumulation
under the mower blade.
Repairs to electrical machines must always be performed only by qualified electricians.
Please do not repair them yourself.
In the case of faults and defects which have not been listed here, please contact the
nearest authorized dealer. This applies in particular to appliances with electrical motors,
as when these are repaired they must always undergo an insulation protection test.
Your authorized dealer will also help you if you do not wish to perform any of the
Remedy
maintenance work described here yourself.
Connect the plug C2 .
Check the fuse.

19 TECHNICAL DATA

Get it checked by an
authorised workshop.

Motor

Set a higher cutting height I .
Machine tilts when starting it.
Clean the cutting chamber of
grass, ensure that the gap
between fan and housing is

Mower

kept clean (pull the plug
first!).
Get it checked by an
authorised workshop.
Have it checked by an
authorized dealer
Pull drive switch bar G .
Have it checked by an
authorized dealer.
Have it checked by an
authorized dealer
Have it sharpened and
balanced by an authorised
workshop Q .
Set higher cutting height I .
Adapt mowing speed, switch
motor drive off if necessary.

Sound power level

If grass is long, the mowing
lanes may need to overlap
further.
A perceptible improvement

Sound pressure level

can be achieved by using a
scarifier.
Empty the collecting bag L .
Set higher cutting height I .

Vibrations

Vibrations on the lawnmower's handlebar;
Adapt mowing speed, switch
measured according to EN60335-2-77
motor drive off if necessary.
Measuring inaccuracy; according EN12096
Allow the lawn to dry.
Have it sharpened and
balanced by an authorised

20 ORIGINAL SPARE PARTS

workshop.
Conversion kit for mulching system
Set higher cutting height I .
Convert mower to rear
Roller bearing grease
ejection U2 + S1 and mow
Cutter bar
lawn with high cutting height
first.
Adapt driving speed, switch
motor drive off if necessary.
Set higher cutting height I .
Declaration of Conformity
10
Insufficient overlap
between mowing lanes.
Grass is damp.
Motor
Connection voltage
Power
Motor speed
Housing
Cutting width
Cutting heights Central, (15), 25, 30, 40, 45, 55, 60, 70, 80 mm
Adjustable-height handlebar
Grass collector capacity
Speed
Weight
Length
Width
Height
Wheels front / rear
Bearing front
Bearing rear
Guaranteed sound power level;
measured according to 2000/14/EC
Emission sound pressure level at operator's workplace;
measured according to EN60335-2-77
Measuring inaccuracy; according to ISO 4871
see the back, after the last language
If grass is long, the mowing
lanes may need to overlap
further.
Set higher cutting height I .
Allow the lawn to dry.
Alternating current motor
230 V
1700 W
3000 min
Die-cast aluminium
430 mm
3-way
65 litres
2,4 – 3,6 km/h
35 kg
1565 mm
500 mm
1025 mm
Ø 180 mm / Ø 200 mm
Cup-and-cone bearing
Cup-and-cone bearing
L = 96 dB(A)
wa
L = 82 dB(A)
pA
3 dB
a = 2.5 m/s
hW
1.3 m/s
BSA632
SAA11300
For safety reasons, the cutter bar must
always be replaced by an authorised
workshop.
This workshop has the respective spare
part numbers for the cutter bar available.
-1
2
2