Jacuzzi J-400 Serie Manuel D'installation page 67

Programming the Auto-Heating Mode
This mode indicates the cold zones where the heating times are
longer due to the lower ambient temperature; the temperature of
the water depends on that set the value of which is used as a
reference by the system to automatically activate the heater.
Note: If you elect to use Auto-Heating, you can skip this sec-
tion. Auto-Heating is the default spa setting.
Press button B to enter the Heating Menu. Use the Quad Key-
pad to down button to select Auto-Heating.
HEATING
Eco-Mode
ENERGY EFFICIENT
Auto-Heating
Select
Programmable
Press to Save
2
If you elect to use this mode, press the Splash button on the
Quad Keypad. The display will confirm your selection and will be
displayed briefly then return to the Heating submenu.
AUTO-HEATING
24-hour Heating
Enabled
To exit the submenu, press button D to return to the Settings 1
Menu. If you have programmed the Auto-Heating cycle you will
see the Thermometer with wavy lines icon next to word Heating
on the display.
Programmable Heating Mode
This mode is indicated in the temperate zone where the heating
times are lower thanks to the higher ambient temperature; the
temperature of the water depends on that set but only when a
programmed filtration cycle is active (unless the "summer" mo-
de intervenes, see relative chapter).
From the Heating Menu, use the Quad Keypad Down button to
select the programmable setting, then press the Splash button
to enable selection.
HEATING
Eco-Mode
ENERGY EFFICIENT
Auto-Heating
Select
Programmable
Press to Set
2
I
You are allowed to have two separate programs in the pro-
grammable mode, you can elect to use both or just one. Press
the Splash button to enter the submenus for "Program A".
I
From this menu, you can set the days, times, and duration. With
"Day Settings" selected press the Splash button on the Quad
Keypad to access the submenus.
AUTO-HEATING
24-hour Heating
Enabled
SETTINGS 1
Heating
UV Light
0 Days
1
Filter
OFF
Press to
2
set filter or UV timer
PROGRAMS
Program A
Program A
A
Program B
Select
Press to Enter
2
PROGRAM A
Day Settings Day Settings
Start Time
Duration
A
Press to Enter
2
I
When you enter the submenu, you can choose the day(s) you
would like "Program A" to run for a heating cycle. Press the Up
or Down button (on the Quad Keypad) to scroll through and
choose the days you would like the heater to activate. Press the
Left or Right button to turn "ON" (
that day.
Press the Splash button once to save settings.
Press button D to return to the submenu to continue program-
ming the start time and duration.
PROGRAM A
Day Settings
Start Time 1PM Start Time
Duration
A
Press to Save
2
I
Press the Down button on the Quad keypad to select "Start
Time". Press the Left or Right button on the Quad Keypad to se-
lect the time you wish the spa to run. Press the Down button to
access the "Duration" submenus.
Note: If you are using a standard 12-hour period, you will
see the hour displayed as "1PM." For the 24-hour period it will
read "1300."
Now you will need to adjust the cycle "Duration". Cycle duration
range is adjustable from 0 (OFF) to 6 hours. Press the Left or
Right button on the Quad Keypad to make adjustments in in-
crements of 1 hour.
Note: The default "Duration" is OFF.
I
Press the Splash button on the Quad Keypad to save your
changes and return to the Heating Menu. At this point you can
program a Secondary Heating Mode (Program B) or press but-
ton B to enter the "Settings 2" Menus.
Program B Heating Mode
To program the Secondary Heating mode press the Down but-
ton on the Quad Keypad to access the "Program B" settings.
Press the Splash button to enter the submenus for Program B.
PROGRAMS
Program A
Program B Program B
B
Press to Enter
2
From this menu, you can set the days, times, and duration. With
"Day Settings" selected, press the Splash button on the Quad
Keypad to confirm selection.
When you enter the submenu, you can choose the day (s) you
67
PROGRAM A
Monday
Tuesday
Wednesday
Select
Thursday
A
Friday
Saturday
Sunday
2
Press to Save
) or "OFF" the heater for
PROGRAM A
Day Settings
Start Time
Select
Duration Duration
OFF
A
Press to Save
2
PROGRAM B
Day Settings Day Settings
Start Time
Select
B Duration
Press to Enter
2
OFF
OFF
Select
OFF
OFF
OFF
OFF
Select
Select