Bluetooth Playback; Bluetooth Setup - Yamaha DRX-730 Mode D'emploi

Masquer les pouces Voir aussi pour DRX-730:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Bluetooth playback

With an optional Yamaha YBA-10 Bluetooth Wireless
Audio Receiver connected to the DRX-730's DOCK
jack, you can enjoy the music stored on your
Bluetooth device, for example, a Bluetooth-
compatible music player or mobile phone, through
the DRX-730's speakers in high quality. You can also
use the DRX-730's remote control to control music
playback on your Bluetooth device.
Notes:
• Set the DRX-730 to standby and disconnect its
power cable before connecting or disconnecting
the Yamaha YBA-10.
• Refer to the Yamaha YBA-10 owner's manual for
details on using the YBA-10.
• Refer to your Bluetooth device owner's manual for
details on using your Bluetooth device.
• Depending on your Bluetooth device model and
its firmware version, some playback functions
may not work as expected, and some may not
work at all.

Bluetooth setup

Using the dock cable supplied with the Yamaha
YBA-10, connect one end of the cable to the
Yamaha YBA-10, and connect the other end to the
DOCK jack on the DRX-730's rear panel.
MAINS
HDMI
CLASS 2 WIRING
CABLAGE CLASSE 2
R
6
MIN
SPEAKER
SUBWOOFER
OUT
IN
SPEAKERS
OUT
AUX
Yamaha YBA-10
AM
ANT
GND
FM
ANT
75
UNBAL.
P
P
R
B
Y
R
OUT
VIDEO
COMPONENT
OPTICAL
DOCK
VIDEO OUT
DIGITAL
Dock cable
(supplied with
Yamaha YBA-10)
Chapter 7: Portable Device Playback
Bluetooth pairing
Before you can use a Bluetooth device with the
DRX-730, you must pair, or register it with the
Yamaha YBA-10.
1
Press DOCK to select the DOCK input source.
2
Turn on the Bluetooth device and make sure
it's discoverable.
3
Press and hold down BLUETOOTH ON for 3
seconds to start pairing.
Pairing starts, the DOCK indicator flashes, and
"Searching... " appears on the display.
During pairing, the Yamaha YBA-10 searches for
compatible Bluetooth devices and registers any
that are found. Pairing only needs to be
performed when a Bluetooth-device is used with
the Yamaha YBA-10 for the very first time, or
when the pairing information has been deleted.
See the Yamaha YBA-10 owner's manual for more
details on pairing.
To cancel pairing, press BLUETOOTH OFF.
4
Make sure the Bluetooth device has detected
the Yamaha YBA-10.
The Yamaha YBA-10 will appear as "YBA-10
YAMAHA" or something similar on the Bluetooth
device.
5
On the Bluetooth device, select the Yamaha
YBA-10, and then enter the pass key "0000".
When pairing is complete, the message
"Completed" appears on the display.
Note:
• Pairing will be cancelled if no compatible
Bluetooth devices are found within 8 minutes, the
input source is changed on the DRX-730, or the
DRX-730 is set to standby.
Connecting Bluetooth devices
Once a Bluetooth device has been paired with the
Yamaha YBA-10, you can connect to it and play the
music stored on it.
1
Press DOCK to select the DOCK input source.
2
Press BLUETOOTH ON.
The Yamaha YBA-10 attempts to connect to the
last Bluetooth device used or paired and
"Searching... " appears on the display.
When a connection is established, "BT
connected" appears on the display.
7
47
En

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

Pianocraft drx-730

Table des Matières