Important Safety Notes - Martin Yale Intimus 45SC2 Instructions D'opération

Translation of the Original Operation Manual
GB
Übersetzung der Originalbetriebsanleitung

IMPORTANT SAFETY NOTES

<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by "one person only".
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
CONTROLS:
1 = Mains plug (fi g. 2)
When the machine is fi rst plugged in it is
not on.
2 = Function buttons (fi g. 1)
"Ready"/ "Off" / "Stop"
This button has three functions:
a) "Ready"
The machine changes to "Ready" if you
press this button briefl y.
At the same time the integral LED
display comes on.
b) "Off"
The machine switches off if it is in the
"Ready" mode and the button is held
down for about 3 seconds.
Note: The machine
automatically if it is not used for about 5
minutes.
c) "Stop"
If you press this button briefl y when the
cutters are running they switch off and
stop.
6
7
8
2
fi g. 1
<< Danger of injury!
<< In case of danger switch the machine off
<< Always unplug the machine from the
3 = Forwards button (fi g. 1)
This button has two functions:
a) If this button is pressed briefl y, the
cutting mechanism runs forwards for a
few seconds, e.g. to remove remaining
material from the cutting mechanism.
At the same time the integrated LED
display
b) If this button is pressed and held
for approx. two secs., the cutting
mechanism runs forwards continually
and materials to be shredded can be fed
into the machine. At the same time the
integrated LED display
4 = Reverse button (fi g. 1)
switches off
If you press this button the cutters run
backwards for a short time. At the same
time the integral LED display
5 = Light barrier (Forward motion) (fi g. 3)
The shredding procedure starts as soon
as material is fed into one of the two feed
slots. At the same time the integral forward
button LED display
3
9
10
11
1
4
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery, long hair or other loose
objects away from opening!
Never insert fi ngers into
opening!
with the mains switch, or with the emer-
gency switch, or unplug the machine!
mains power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
OPERATION
lights up.
lights up.
comes on.
comes on.
fi g. 2
5
INITIATION
AREA OF APPLICATION:
The intimus 45/60/90SC2/CC3/CC4
shredder is a machine used for shredding general
documents and
data carriers such CD's, DVD's, credit cards and
3.5" diskettes.
The machine must only be used to
shred paper, credit cards and CD's,
DVD's and 3.5" diskettes.
Shredding other sorts of data carriers
may cause damage to the machine (e.g.
damage to the cutters etc.).
INSTALLATION:
- Unpack the machine and put it together.
- Fit the plastic bag onto the bag frame.
- Connect the machine to the power with the plug
(1) (Fig. 2) (For information on the right fuse for
the plug see "TECHNICAL DATA").
The socket outlet shall be installed
near the equipment and shall be easily
accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
6 = Control display (fi g. 1)
"Material jam in
"Simultaneous material feed" / "Light
barrier covered when door opens or
when machine turned on"
For the procedures see the relevant
description under the "MALFUNCTION"
section.
a) "Material jam in machine"
Comes on when too much material has
been fed into the cutters. The cutters
jam, then run in reverse for a short time
and stop. The motor switches off.
b) "Simultaneous material feed"
Comes on when material has been fed
into both slots at the same time. The
cutters stop, then run in reverse for a
short time and stop. The motor switches
off.
c) "Light barrier covered
when door open"
Comes on when there is still material in
one of the two feed slots when the door
is opened. The cutters stop. The motor
switches off.
d) "Light barrier covered
when machine turned on"
Comes on when there is still material
in one of the two feed slots when the
machine is switched on.
13
12
fi g. 3
data
machine"/
5