Important Safety Notes - Martin Yale MY 1000 SC Instructions D'opération

GB

IMPORTANT SAFETY NOTES

<< The machine may not be operated by
more than one person at any given time!
The machine was designed for safe
operation by "one person only".
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.).
<< Keep children away from the machine.
This machine's design and safety concept
are based on adult dimensions (feeder
route, safety cut-off switches, etc.) to ensure
that it can be operated safely by adults
only.
<< Repairs may only be performed by
trained personnel.
EXPLANATION OF THE CONTROLS:
1 = Function switch (fig. 1)
(on / off / reverse)
This switch is for the following functions:
- position „ "
machine is ready for operation
- position „ "
machine is switched off
- position „ "
cutting blades are reversing
2 = Light barrier (forward running) (fig. 2)
The shredding operation starts as soon as
material is fed into one of the two feed slots.
3 = Pilot lamp „ready" (fig. 1)
Lights when the pushbutton switch (1) is
operated.
4 = Pilot lamp "material jam" (fig. 1)
Lights when too much material is fed to the
cutters. The cutting system blocks and stops.
The motor is switched off.
5 = Pilot lamp "motor overload" (fig. 1)
Lights up if the motor is overloaded. The
machine cannot be started again until the
motor has cooled down.
fig. 1
All manuals and user guides at all-guides.com
<< Keep all loose articles of
<< Never insert fingers into opening.
Serious injury may result!
<< In case of danger switch the
STOP machine off with the mains switch,
or with the emergency switch, or
unplug the machine.
<< Always unplug the machine from
the mains power supply before
opening the machine.
OPERATION
The shredder may not be used as a
step ladder or as a seat. Danger of
falling due to breakage!
MATERIAL FEED:
- Turn the function switch (1) (fig. 1) in position
„ ". The pilot lamp (3) (fig. 1) lights up.
- Feeding paper
Feed the paper into the cutting system through
the paper feed slot (6) (fig. 2).
- Feeding data media
Feed the data media (CDs, DVDs or credit
cards) into the cutting system one by one through
the separate security feed slot (7) (fig. 2).
- The machine automatically switches to forward
running and pulls the material in. The machine
switches off again automatically when shredding
is completed.
4
5
3
1
2
fig. 2
SCOPE OF APPLICATION:
clothing, ties, jewelery, The MY1000SC / MY1000CC // MY2000SC /
long hair or other loose
MY2000CC data shredder is designed for
objects away from shredding general printed material and data media
opening, injury may such as CDs, DVDs and credit cards.
result!
INSTALLATION:
- Unpack and set machine upright.
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA").
EMPTYING THE RECEPTACLE (Fig. 3):
When the shredded material becomes visible in
the "receptacle full" window (8) (fig. 3) it is time to
empty the receptacle.
Proceed as follows:
- Remove the receptacle from in front of the
machine and empty its contents.
- Replace the empty receptacle under the machine
and push all the way to the back.
Note: The machine will only run when the
receptacle is pushed completely under the
machine.
7
6
4
MY 1000 SC
MY 1000 CC
MY 2000 SC
MY 2000 CC
INITIATION
This machine should only be used for
shredding paper and credit cards. The
models MY2000SC and MY2000CC can
also be used to shred CDs and DVDs.
Any attempt to shred other types of data
medium may result in damage to the
machine (e.g. destruction of the cutting
mechanism etc.).
The socket outlet shall be installed
near the equipment and shall be easily
accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
OPERATION
Never feed the shredder with a quantity
of material exceeding the maximum
indicated. Refer to the TECHNICAL
DATA section.
Should the machine become overloaded,
follow the instructions under "MATERIAL
JAM IN MACHINE"
"MALFUNCTIONS".
8
fig. 3
under