Evolution FURYTWIN1251 Manuel D'instructions page 8

f) Don't force the tool. It will do the job better and safer if
used at the rate for which it was designed.
g) Use proper extension cord. Make sure your extension
cord is in good condition. When using an extension cord,
be sure to use one heavy enough to carry the current your
machine will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and possible overheating.
h) Wear proper apparel. Do not wear loose clothing, gloves,
neckties, rings, bracelets, or other jewellery which may get
caught in moving parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
i) Always use safety glasses. Also use face or dust mask
if cutting operation is dusty. Everyday eyeglasses only have
impact resistant lenses, they are NOT safety glasses.
j) Secure work. Use clamps to hold work when practical.
k) Don't overreach. Keep proper footing and balance at all times.
l) Maintain tools with care. Keep tools sharp and clean
for best and safest performance. Follow instructions for
lubricating and changing accessories.
m) Disconnect tools before servicing and when changing
accessories, such as blades.
n) Reduce the risk of unintentional starting. Make sure
switch is in off position before plugging in.
o) Use recommended accessories. Only use genuine
Evolution accessories.
p) Check for damaged parts. Before further use of the tool,
a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and perform
its intended function - check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or replaced.
q) Keep hands out of the path of the saw blades.
r) Never reach around the saw blades.
s) Turn off tool and wait for saw blades to stop before
moving workpiece.
t) Disconnect power before changing blades, servicing
or cleaning.
u) Never carry the tool by the power cord. Carrying the
tool by the power cord could cause damage to the insulation
or the wire connections resulting in the possibility of electric
shock or fire.
8
®
SPECIFICATIONS
SPECIFICATIONS
FURYTWIN 125mm (5˝)
Motor (230V or 110V 50Hz) (Watts):
RPM No Load (min
Max Cut Depth:
Weight:
Blade Dimensions
Maximum Diameter:
Thickness:
ASSEMBLY
Your Evolution Power Tools Twin Blade Saw is shipped
complete. Remove all the contents from the box and inspect
to ensure no damage has occurred during shipping, and that
the items listed below are included:
Description
Instruction Manual
125mm TCT Blade (Fitted)
Spanner
Assist Handle
Lubrication Unit (Fitted)
CAUTION!
SAW FROM THE POWER SOURCE BEFORE MAKING ANY
ADJUSTMENTS.
OPERATION
OPERATION
Before commencing any operations, please check the
following:
1. Power source
Ensure that the power source to be utalized conforms to the
power requirements specified on the machines nameplate.
2. Power Switch
Ensure that the power switch is in the OFF position. If the
plug is connected to a power source with the switch in the
ON position, the machine will start operating immediately.
This could cause a serious accident.
3. Extension cord
When the work is remote from the power source, use an
extension cord of sufficient thickness and rated capacity. The
extension cord should be kept as short as possible, and routed
so that it does not constitute a trip or other safety hazard.
4. Checking the Blades
Check that the blades are the specified ones, and are not
cracked, broken or bent. Do not use the machine if there is
any doubt about the integrity of the blades.
www.evolutionproject.com
-1 ):
Blade A: 1.5mm
Blade B: 1.7mm
ALWAYS DISCONNECT THE TWIN BLADE
GB
850W
5500min -1
28mm
3.2kg
125mm
Qty
1
1 Pair
1
1
1
GB