General Power Tool Safety Warnings - MIRKA CEROS Mode D'emploi

Masquer les pouces Voir aussi pour CEROS:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

General Power Tool Safety Warnings
WARNING Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury. 
Save all warnings and instructions for future reference. 
The term "power tool" in the warnings refers to any power supplied (corded) power tool or battery-
operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do  n ot  o perate  p ower  t ools  i n  e xplosive  a tmospheres,  s uch  a s  i n  t he  p resence  o f  fl ammable 
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use 
any adapter plugs with grounded (earthed) power tools. Unmodified plugs and matching 
outlets will reduce risk of electric shock.
b) Avoid  b ody  c ontact  w ith  e arthed  o r  g rounded  s urfaces,  s uch  a s  p ipes,  r adiators,  r anges  a nd 
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will in-
crease the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power 
tool. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled
cords increase the risk of electric shock.
e)  When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f ) If operating a power tool in a damp location is unavoidable, use a ground fault circuit 
interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
3) Personal safety
a) Stay  a lert,  w atch  w hat  y ou  a re  d oing  a nd  u se  c ommon  s ense  w hen  o perating  a   p ower  t ool.  D o 
not  u se  a   p ower  t ool  w hile  y ou  a re  t ired  o r  u nder  t he  i nfluence  o f  d rugs,  a lcohol  o r  m edication.
A moment of inattention while operating power tools may result in serious personal injury. 
b) Use  personal  protective  equipment.  Always  wear  eye  protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries. 
c) Prevent unintentional starting. Ensure the switch is in the off-position before connect-
ing to power source and/or battery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energising power tools that have the switch on invites 
accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury. 
e) Do not overreach. Keep proper footing and balance at all times. This enables better control
of the power tool in unexpected situations.
f ) Dress  properly.  Do  not  wear  loose  clothing  or  jewellery.  Keep  your  hair,  clothing  and 
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in mov-
ing parts.
g) If devices are provided for the connection of dust extraction and collection facilities, en-
sure these are connected and properly used. Use of dust collection can reduce dust related
hazards.
4

Publicité

Table des Matières
loading

Table des Matières