Beretta Exclusive C.A.I. Série Manuel D'installation Et D'utilisation page 17

C.A.I.: programmable parameters
N° DESCRIPTION PARAMETERS
PAR.
1 GAS TYPE
3 INSULATION LEVEL OF BUILDING (+) (*)
10 DHW MODE
11 DHW CIRCUIT MAXIMUM SET-POINT
12 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
13 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
14 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
20 CH MODE
21 HEATING CIRCUIT MAXIMUM SET-POINT
22 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
28 MAX HEATING POWER REDUCTION TIMER
29 FORCED HEATING SHUT DOWN TIMER
30 HEATING TIMER RESET FUNCTION
40 DHW THERMOSTAT OPERATING MODE
41 DHW PREHEATING FUNCTION
42 S.A.R.A. FUNCTION
43 S.A.R.A. BOOSTER FUNCTION
44 THERMOREGULATION FUNCTION
45 INCLINATION THERMOREGULATION CURVE (OTC) (*)
48 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
50 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
61 DHW ANTIFREEZE FUNCTION TEMPERATURE (ON)
62 HEATING ANTIFREEZE FUNC. DELIVERY TEMP. (ON)
85 SEMI-AUTOMATIC FILLING
86 AUTOMATIC FILLING PRESSURE (ON)
MIX C.S.I.: programmable parameters
N° DESCRIPTION PARAMETERS
PAR.
1 GAS TYPE
2 BOILER POWER
3 INSULATION LEVEL OF BUILDING (+) (*)
10 DHW MODE
11 DHW CIRCUIT MAXIMUM SET-POINT
12 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
13 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
14 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
20 CH MODE
21 HEATING CIRCUIT MAXIMUM SET-POINT
22 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
28 MAX HEATING POWER REDUCTION TIMER
29 FORCED HEATING SHUT DOWN TIMER
30 HEATING TIMER RESET FUNCTION
40 DHW THERMOSTAT OPERATING MODE
41 DHW PREHEATING FUNCTION
42 S.A.R.A. FUNCTION
43 S.A.R.A. BOOSTER FUNCTION
44 THERMOREGULATION FUNCTION
45 INCLINATION THERMOREGULATION CURVE (OTC) (*)
48 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
50 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
61 DHW ANTIFREEZE FUNCTION TEMPERATURE (ON)
62 HEATING ANTIFREEZE FUNC. DELIVERY TEMP. (ON)
85 SEMI-AUTOMATIC FILLING
86 AUTOMATIC FILLING PRESSURE (ON)
(*) parameters shown only with external sensor connected and parameter 44 in 1 (AUTO).
(+) for well-insulated buildings select values close to 20, for badly insulated buildings choose values close to 5.
Parameter 45 "Inclination of thermoregulation curve (OTC)"
The curve must be chosen according to the geographical area and the type of
installation.
UNIT OF MIN
MEASURE
1 Methane
2 LPG
3 Methane France
min 5
0 (OFF)
1 (Instantaneous)
2 (Mini-tank)
3 (External water-tank with thermostat)
4 (External water-tank with sensor)
° C 40
0 (OFF)
1 (ON)
2 (zone valves + remote control panel)
° C 40
min 0
min 0
- 0
0 (OFF)
1 (AUTO)
2 (ON)
0 (OFF)
1 (AUTO)
2 (ON)
0 (OFF)
1 (AUTO)
0 (OFF)
1 (AUTO)
0 (OFF)
1 (AUTO)
- 2,5
°C 0
°C 0
0 (disabled)/1 (enabled)
bar 0.4
UNIT OF MIN
MEASURE
1 Methane
2 LPG
3 Methane France
26 (26kW)
30 (30kW)
34 (35kW)
min 5
0 (OFF)
1 (Instantaneous)
2 (Mini-tank)
3 (External water-tank with thermostat)
4 (External water-tank with sensor)
° C 40
0 (OFF)
1 (ON)
2 (zone valves + remote control panel)
° C 40
min 0
min 0
- 0
0 (OFF)
1 (AUTO)
2 (ON)
0 (OFF)
1 (AUTO)
2 (ON)
0 (OFF)
1 (AUTO)
0 (OFF)
1 (AUTO)
0 (OFF)
1 (AUTO)
- 2,5
°C 0
°C 0
0 (disabled)/1 (enabled)
bar 0.4
Tm. - 20
OTC = 10 x
20 - Te.
17
MAX DEFAULT
(setted in factory) (setted by techn. assist. centre)
1-2
20 5
1
60 60
1
80 80
20 15
20 3
1 0
1
1
1
1
1
40 20
10 4
10 6
1
0.8 0.6
MAX DEFAULT
(setted in factory) (setted by techn. assist. centre)
1-2
26-30-34
20 5
1
60 60
1
80 80
20 15
20 3
1 0
1
1
1
1
1
40 20
10 4
10 6
1
0.8 0.6
T m. = maximum rated temperature of heating water
T e. = minimum rated external temperature
PARAMETERS
60
80
5
40
0
1
PARAMETERS
60
80
5
40
0
1