Notes For Instructions; Use; Storage - Proficook PC-WKS 1020 G Mode D'emploi

Notes for Instructions

• When connecting to the outlet a buzzer sounds twice.
• As soon as you take the kettle from the base, a buzzer
will sound. The appliance returns to standby mode.
• Using the function buttons, you can select the optimum
water temperature of your drink.
• You can heat up water to the following specific tempera-
tures: 70 °C, 80 °C, 90 °C and 100 °C.
• Using an additional function, you can keep the tempera-
ture of the water hot at 70 °C, 80 °C, 90 °C.
• You can use the tea strainer to prepare tea in your kettle.
Preparation
Before using for the first time, boil fresh water at least three
times in the appliance. Use only water without any additives
or ingredients.
NOTE:
Always use fresh, cold water.

Use

1. Place the appliance on a flat surface.
2. Opening the lid
Press the (3) button. The opener springs open. You can
remove the lid by pulling upwards.
3. Then fill in the water (max. 1.7 litre).
You can read the filling level on the water level indicator
of the kettle.
4. In order to close the lid, press the (3) button. The lid must
audibly lock into place.
5. Place the kettle flush on the base.
Operation
1. Select a temperature using the buttons 8 to 11. The light
on the button will light up.
2. Press the button. The light on the button will light up.
NOTE:
• The light on the temperature button will flash whilst the
water heats up.
• If the temperature has been reached, you will hear two
buzzers.
• The light on the button will go out.
• The light on the temperature button will light up until
you take the jug from the base.
Keep warm function:
• You can keep the water hot for half an hour at the
following temperatures: 70 °C, 80 °C and 90 °C.
• To do this, press the button after you have selected
a temperature.
• The light on the button will light up.
• The keep warm will remain active, even if you take the
jug from the base for up to a minute.
38
PC-WKS1020G_IM_new2
Keep warm function:
• Not for 100 °C! The keep warm function cannot be
combined with this temperature.
Quick start:
• Press the button after putting the jug on to boil.
• The water will be heated to 100 °C.
Ending / Terminating Operation
There are two options to interrupt the boiling process or to
terminate it:
• The appliance will switch off after the boiling process.
• You can press the button again in order to end the
boiling process.
The light on the button will go out.
WARNING: DANGER OF SCALDING!
• When pouring the water out, keep the lid closed.
• During operation the housing becomes hot. Do not
touch it and allow the appliance to cool down before
storing it away.
• Remove the mains plug.
• Emptying the water container.
Tea strainer
You can replace the lid of the kettle with the tea strainer.
See the illustration.
1. In order to open the strainer, rotate it slightly in an anti-
clockwise direction.
2. Add the tea and close the strainer again.
3. Put the tea strainer on instead of the lid.
4. Use the plunger to determine when and for how long the
tea is supposed to brew.
CAUTION:
• To prepare tea, refer to the "TeaMax" mark.
• Bring 1.2 litres (max.) of water to the boil.
• The tea strainer should only be immersed in water if
the desired temperature has been reached.
• The tea strainer will continue to drip!

Storage

• Clean the appliance as described and allow it to dry.
• We recommend that you keep the appliance in the origi-
nal packaging if it will not be used for long periods.
• Always store the appliance out of the reach of children in
a dry, well ventilated place.
08.03.18