Machine Structure - Description - Advance Adfinity 17ST Instructions D'utilisation

INSTRUCTIONS FOR USE

MACHINE STRUCTURE - DESCRIPTION

Control panel (1) - It is the area where machine controls are located, see Control and Switch Description paragraph.
Handlebar (2) - Grasp it and use it to maneuver the machine.
Solution/clean water filter (3) - It filters the solution/clean water before supplying it to the brush.
Solution/clean water tap (4) - It closes the solution/clean water flow.
Battery charger data inspection window (5) - See Battery Warning Light Description paragraph.
Battery charger cable (6) - Connect it to the electrical mains to charge the batteries.
Battery charger cable holder (7) - Use it to roll up the battery charger cable when it is not in use. Fasten the cable safely.
Recovery water drain hose plug (8) - Open it and lower the pipe to drain the recovery water from the tank.
Water removable filler hose (optional) (9) - For easily filling the tank with water.
Squeegee lifting/lowering lever (10) - To lift or lower the squeegee.
Deck lifting/lowering pedal (11) - It has the following functions:
(11a) Deck lifting
(11b) Deck lowering
Battery connector (red) (12) - It connects the batteries to the machine electrical system. This connector also works as
EMERGENCY switch, to stop immediately all functions. If necessary, grasp the handle and disconnect the connector by pulling
it strongly.
Rear steering wheels (13) - They allow the machine to steer.
Front wheels on fixed axle (14) - They bear the machine weight.
Squeegee vacuum hose (15) - It conveys the recovery water from the squeegee to the recovery water tank. To easily clean it,
remove the plug (35).
Recovery water drain hose (16) - It drains the recovery water from the tank.
Solution/clean water drain and level check hose (17) - It is equipped with level marks to check the solution/water level in the
tank. Disconnect the upper end to drain the tank.
Brush/pad-holder deck (18) - On the deck, brush or pad-holder and the relevant motors are installed.
Brush/pad-holder (19) - The machine can be equipped with one brush or one pad-holder with pad.
Solution/clean water tank (20) - It contains the solution/clean water.
Recovery water tank (21) - It contains the recovery water collected by the squeegee and vacuumed.
Recovery water tank cover (22) - It hermetically closes the recovery water tank.
Can holder (23) - Compartment to store a can or small objects.
Pocket (optional) (24) - Elastic retainer for documents.
Squeegee (25) - It collects the solution after scrubbing.
Squeegee mounting handwheels (26) - They fasten the squeegee to the machine.
Squeegee balance adjusting handwheel (27) - To adjust the squeegee blade position.
Machine straight forward movement adjusting handwheel (28) - Turn it clockwise or counter-clockwise for machine straight
forward movement.
Machine forward speed adjustment handwheel (29) - Turn it clockwise or counter-clockwise to change the machine forward
speed.
Recovery water tank cover (open)
By turning the retaining plate (32), it can be removed.
(30a) Opened to be cleaned.
(30b) Completely opened.
Tank cover gasket (31) - The gasket must be integral for an efficient vacuuming of the recovery water.
Cover retaining plates (32) and (33) - Turn the retaining plate (32) to remove the tank cover.
Serial number plate/technical data/conformity certification (34) - It contains the machine data.
Plug for squeegee vacuum hose cleaning (35) - Remove it to clean the vacuum hose.
Vacuum grid with automatic shut-off float (36) - Keep it clean, to avoid a stuck in the vacuum system.
Solution filler neck (37) - For easily filling the tank with solution. Use only low-foam detergents.
Foam filter (38) - It prevents debris or foreign materials from entering into the tank.
Compensation hole (39) - Keep it clean, for an efficient vacuuming of the recovery water.
Recovery water tank (open) (40) - Empty and lift it to reach the batteries and the detergent tank.
Tank lifting handle (41) - Grasp it to lift the tank, only when it is empty.
Tank safety cable (42) - It keeps the tank opened.
Vacuum system motor cover (43) - It retains the sound-deadening filter and protects the vacuum system motor.
8 9096912000(1)2006-09