Advance Adfinity 17ST Instructions D'utilisation page 6

INSTRUCTIONS FOR USE
WARNING!
– Before using the battery charger, ensure that frequency and voltage values, indicated on the machine serial number plate,
match the electrical mains voltage.
– Do not pull or carry the machine by the battery charger cable and never use the battery charger cable as a handle. Do not
close a door on the battery charger cable, or pull the battery charger cable around sharp edges or corners. Do not run the
machine on the battery charger cable.
Keep the battery charger cable away from heated surfaces.
– Do not charge the batteries if the battery charger cable or the plug are damaged. If the machine is not working as it should,
has been damaged, left outdoors or dropped into water, return it to the Service Center.
– To reduce the risk of fire, electric shock, or injury, do not leave the machine unattended when it is plugged in. Before
performing any maintenance procedure, disconnect the battery charger cable from the electrical mains.
– Do not smoke while charging the batteries.
– Always protect the machine against the sun, rain and bad weather, both under operation and inactivity condition. Store
the machine indoors.
– Do not allow to be used as a toy. Close attention is necessary when used near children.
– Use only as shown in this Manual. Only Nilfisk-Advance recommended accessories must be used.
– Take all necessary precautions to prevent hair, jewelry and loose clothes from being caught by the machine moving parts.
– Do not leave the machine unattended without being sure that it cannot move independently.
– Do not use the machine on slopes with a gradient exceeding the specifications.
– Do not use the machine in particularly dusty areas.
– While using this machine, take care not to cause damage to people or objects.
– Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.
– Do not put any can containing fluids on the machine.
– The machine operating temperature must be between +32°F and +104°F (0°C and +40°C).
– The machine storage temperature must be between +32°F and +104°F (0°C and +40°C).
– The humidity must be between 30% and 95%.
– Do not use the machine as a means of transport.
– Do not use the machine on slopes with an inclination higher than 2%.
– Do not allow the brushes to operate while the machine is stationary to avoid damaging the floor.
– In case of fire, use a powder fire extinguisher, not a water one.
– Do not tamper with the machine safety guards and follow the ordinary maintenance instructions scrupulously.
– Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged. Always keep the
openings free from dust, hairs and any other foreign material which could reduce the air flow.
– Do not remove or modify the plates affixed to the machine.
– If the machine is used according to the instructions, the vibrations are not dangerous. The machine vibration level is less
2
than 98.4 in/s (2.5 m/s
– This machine cannot be used on roads or public streets.
– Pay attention during machine transportation when temperature is below freezing point. The water in the recovery tank or
in the hoses could freeze and seriously damage the machine.
– Use the brushes and pads supplied with the machine and those specified in the Instructions for Use Manual. Using other
brushes or pads could reduce safety.
– In case of machine malfunctions, ensure that these are not due to lack of maintenance. Otherwise, request assistance
from the authorized personnel or from an authorized Service Center.
– If parts must be replaced, require ORIGINAL spare parts from a Dealer or Authorized Retailer.
– To ensure the proper and safe operation of the machine, have the scheduled maintenance, detailed in the relevant chapter
of this Manual, performed by the authorized personnel or an authorized Service Center.
– Carefully read all the instructions before carrying out any maintenance/repair procedure.
– Do not wash the machine with direct or pressurized water jets, or with corrosive substances.
– The machine must be disposed of properly, because of the presence of toxic-harmful materials (batteries, etc.), which are
subject to standards that require disposal in special centers (see Scrapping chapter).
4
2
) (98/37/EEC-EN 1033/1995).
9096912000(1)2006-09