120 Vac Grounding Instructions; Machine Description; Machine Structure - Advance SC100 Instructions D'utilisation

ENGLISH
– Do not use the machine if the openings are clogged.
Always keep the openings free from dust, hairs and any
other foreign material which could reduce the air flow.
– Do not remove or modify the plates affixed to the
machine.
– Pay attention during machine transportation when
temperature is below freezing point. The water in the
recovery tank or in the hoses could freeze and seriously
damage the machine.
– Use brushes supplied with the machine or those
specified in the Instructions for use Manual. Using other
brushes could reduce safety.
– In case of machine malfunctions, ensure that these are
not due to lack of maintenance. If necessary, request
assistance from the authorised personnel or from an
authorised Service Center.
– If the machine
• does not work properly
• is damaged
• has water or foam leaks
• has been left outdoors exposed to bad weather
conditions
• is wet or has been dropped into water
turn it off immediately and contact the Advance Service
Center or a qualified technician.
– If parts must be replaced, require ORIGINAL spare parts
from an Authorised Dealer or Retailer.
– To ensure machine proper and safe operation, follow the
relevant scheduled maintenance table in this manual.
– Do not wash the machine with direct or pressurised
water jets, or with corrosive substances.
– The machine must be disposed of properly, because
of the presence of toxic-harmful materials (electronic
components, etc.), which are subject to standards that
require disposal in special centres (see the Disposal
chapter).

120 VAC GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should electrically
malfunction, grounding provides a path of least resistance
for electric current to reduce the risk of electric shock. This
appliance is equipped with a cord having an equipment-
grounding conductor and grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
WARNING!
The machine must be used with an extension power cord
as follows:
– minimum length 15 feet
– type S, or ST, or SO, or STO, or STW
– minimum rate 300V 140/167°F (60/75°C)
DANGER!
– Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service person if you are
in doubt as to whether the outlet is properly grounded.
Do not modify the plug provided with the appliance. If it
will not fit the outlet, have a proper outlet installed by a
qualified electrician.
4
INSTRUCTIONS FOR USE
SC100 - 107408645
– This appliance is for use on a nominal 120V circuit,
and has a grounding plug that looks like the plug (B,
Fig. 6). A temporary adapter (B and C) may be used to
connect this plug to a 2-pole receptacle (B), if a properly
grounded outlet is not available. The temporary adapter
should be used only until a properly grounded outlet (A)
can be installed by a qualified electrician. The green-
colored rigid ear, tab, or the like extending from the
adapter must be connected to a permanent ground such
as a properly grounded outlet box cover. Whenever
the adapter is used, it must be held in place by a metal
screw. Grounding adapters are not approved for use in
Canada.
– Replace the plug if the grounding pin is damaged or
broken.
– The Green (or Green/Yellow) wire in the cord is the
grounding wire. When replacing a plug, this wire must
be attached to the grounding pin only.
Extension cords connected to this machine should be 12
gauge, three-wire cords with three-prong plugs and outlets.
DO NOT use extension cords more than 50 feet (15 m) long.

MACHINE DESCRIPTION

MACHINE STRUCTURE

(Figure 1)
1. Handle
2. Main switch
3. Start/stop push button
4. Solution push button, level 1
5. Solution push button, level 2
6. Empty solution tank warning LED
7. Pedal for release from parking position
8. Squeegee bar lifting/lowering pedal
9. Tank coupling and transport handle
10. Solution tank
11. Solution tank filler plug
12. Solution filter
13. Recovery tank
14. Cleaning deck
15. Brush engagement/disengagement lever
16. Cylindrical brush
17. Squeegee bars
18. Inspection lid
19. Recovery water vacuum hose
20. Air filter cover
21. Recovery tank drain plug
22. Vacuum inlet plug
23. Brush/vacuum motor compartment
24. Rear wheels
25. Transport handle housing
26. Power supply cable holder
27. Power supply cable with connector
28. Serial number plate/technical data/conformity certification
11/2015