Remote Control Unit - JVC DLA-M2000LU Manuel D'instructions

(QJB'/$0ERRN 3DJH  7KXUVGD\ $XJXVW     $0
Controls and Features

Remote Control Unit

On the remote control, the same buttons as on the control
panel of the projector are provided except for the following
buttons. For the same buttons, operation is the same in
principle.
For remote control only:
DIGITAL ZOOM +/-, QUICK ALIGN., FREEZE, ZOOM T/W,
FOCUS +/-
Notes
• The ZOOM T/W buttons work only if the lens unit with a
zooming function is used.
• The following buttons are not used with this projector.
VIC SELECT, SHIFT U/D, SHUTTER
e
w FREEZE OPERATE
HIDE
PRESET MENU
q
ESCAPE VIC SELECT
p
PC
+
9
DIGITAL
ZOOM KEYSTONE VIDEO
–
8
RM-M2000 REMOTE CONTROL UNIT
7
1
Remote control's signal transmitter
2
OPERATE button
When the projector is in the stand-by mode, press this
button one second or more, and the projector is turned
on, causing the OPERATE indicator to light.
Press it one second or more again, and the projector
goes into the cool-down mode, then stand-by mode.
(Refer to page 31.)
* The OPERATE button will not work for approximately 1
minute from when the light-source lamp is turned on. Use
the button after approximately 1 minute.
Memo
While in the cool-down mode (STAND BY indicator is
blinking):
Even if you press the OPERATE button, the projector is not
turned on. Wait until the projector enters stand-by mode
(STAND BY indicator stays lit).
3
MENU button
Use this button to enter or exit the menu mode. The main
menu appears or disappears at the screen. For details,
refer to "Basic Menu Operation" on page 42.
12
4
5
1
2
3
4 6
DIGITAL
ZOOM KEYSTONE VIDEO
–
LENS
5
r
+
U T
SHIFT ZOOM FOCUS
–
D W
t
+ +
QUICK
SHUTTER ALIGN. VOLUME
6
– –
y
u
7
RM-M2000 REMOTE CONTROL UNIT
8
9
p
DLA-M2000LU/M2000SCU/ LCT0940-002A / ENGLISH
5 ∞ 2 3
Cursor ( / / / ) /ENTER button
When using this as the cursor button, press it in the 5
2 3 directions to select menu items or adjust settings.
/
When using it as the ENTER button, press the button
straight down.
ENTER is used in the menu mode. Use to display the
hierarchical menus. Also use when "ENTER" is displayed
against the item on the menu screen or when the "All
reset" selection is confirmed. For details, refer to "Basic
Menu Operation" on page 42.
PC button
Use this button to select a device connected to the PC 1
or PC 2 terminals. Each time you press the button, the
selection alternates between PC 1 and PC 2. (Refer to
page 32.)
* "PC 1" or "PC 2" will be displayed on the top right of the
projected image. (This function can be disabled using the
menu.)
VIDEO button
Use this button to select a device such as a video deck
connected to the AV IN terminal (VIDEO or Y/C input
terminal) of the projector. Each time you press the button,
the selection alternates between Y/C and VIDEO. (Refer
to page 32.)
* "Y/C" or "VIDEO" will be displayed on the top right of the
projected image. (This function can be disabled by the
menu.)
Wired remote control terminal
To use the remote control as a wired unit, connect the
supplied remote cable between this terminal and the
REMOTE terminal on the back of the projector. (Refer to
page 20.)
* The remote control's signal transmitter will stop working
when the cable is connected to this terminal.
KEYSTONE / buttons
Use these buttons to correct a trapezoidal distortion of
the projected image. (Refer to page 34.)
DIGITAL ZOOM +/– buttons
A part of image can be magnified up to four times on the
screen.
Each time the + or – button is pressed, the image is
enlarged or the enlarged image is reduced by a certain
degree. (Refer to page 36.)
* Images which are enlarged with the digital zoom become
less clear.
* Depending on the video signal source (UXGA, etc.), this
button does not work.
ESCAPE button
This button is used in the menu mode to return to the
previous menu. When the main menu is displayed, this
button will cause the menu to disappear. For details, refer
to "Basic Menu Operation" on page 42.
∞
/ /