Remote Control Unit - JVC D-ILA DLA-G150CLU Manuel D'instructions

Eng_Body.fm Page 12 Wednesday, May 15, 2002 10:17 AM
Controls and Features

Remote Control Unit

On the remote control, the same buttons as on the control
panel of the projector are provided except for the following
buttons. For the same buttons, operation is the same in
principle.
For remote control only:
DIGITAL ZOOM T/W, QUICK ALIGN., FREEZE, ZOOM T/
W, FOCUS +/–, SCREEN W/S, PC 1, PC 2, VIDEO, Y/C,
DVI, COMP.
QUICK
ALIGN.
u
y W W
SCREEN SCREEN
S S
t
PC1
r
e
KEYSTONE
w
q
RM-M160 REMOTE CONTROL UNIT
1 Remote control's signal transmitter
2 OPERATE button
When the projector is in the stand-by mode, press this
button one second or more, and the projector is turned
on, causing the OPERATE indicator to light.
Press it one second or more again, and the projector
goes into the cool-down mode, then stand-by mode.
(Refer to page 32.)
* The OPERATE button will not work for approximately 1
minute from when the light-source lamp is turned on. Use
the button after approximately 1 minute.
Memo
While in the cool-down mode (STAND BY indicator is
blinking):
Even if you press the OPERATE button, the projector is not
turned on. Wait until the projector enters stand-by mode
(STAND BY indicator stays lit).
3 HIDE button
Use this button to turn off the image on the screen
temporarily. Pressing it again makes the image to
resume. (Refer to page 35.)
4 FREEZE button
During projection of an image on the screen, press this
button to obtain a still picture.
To restore normal projection, press it again. (Refer to
page 37.)
* Depending on the video signal source (UXGA 60Hz,
SXGA 60Hz), this button does not work.
12
1
OPERATE
2
3
HIDE
FREEZE COMP VIDEO 4
5
PC2 DVI Y/C
6
T T
7
DIGITAL
ZOOM FOCUS
ZOOM
W W
PRESET MENU 8
9
p
EXIT ENTER
DLA-G150CLU / LCT1123-001C / ENGLISH
5 VIDEO button
Use this button to select a device such as a video deck
connected to the AV IN terminal (VIDEO, Y/C or COMP
input terminal) of the projector. Each time you press the
button, the selection alternates among Y/C, VIDEO and
DVI. (Refer to page 33.)
* "Y/C", "VIDEO" or "DVI" will be displayed on the top right
of the projected image. (This function can be disabled by
the menu.)
6 ZOOM T/W buttons
Use these buttons to adjust the projected screen size.
T (Tele): The projected screen size decreases.
W (Wide):The projected screen size increases.
7 FOCUS +/– buttons
Use these buttons to adjust the focus of the projected
video image.
+ : The focus point becomes more distant.
– : The focus point becomes nearer.
8 MENU button
Use this button to enter or exit the menu mode. The main
menu appears or disappears at the screen. For details,
refer to "Basic Menu Operation" on page 43.
9 Cursor buttons 5 ∞ 2 3
/ / /
These buttons are used in the menu mode to select an
item or to set or adjust the value. For details, refer to
"Basic Menu Operation" on page 43.
p ENTER button
This button is used in the menu mode. Use to display the
hierarchical menus. Also use when "ENTER" is displayed
against the item on the menu screen or when the "All
reset" selection is confirmed. For details, refer to "Basic
Menu Operation" on page 43.
q EXIT button
This button is used in the menu mode to return to the
previous menu. When the main menu is displayed, this
button will cause the menu to disappear. For details, refer
to "Basic Menu Operation" on page 43.
w PRESET button
This PRESET button only works as a reset button for the
direct button adjustment of the KEYSTONE button of the
control panel and the DIGITAL ZOOM button of the
remote control. When adjusting the keystone or digital
zoom (when the setting is displayed on the screen) the
adjusted value is reset to that which was set when the
projector was shipped from the factory. Of the menu
items, this button only works for the keystone setting
screen.
e KEYSTONE
/ buttons
Use these buttons to correct a trapezoidal distortion of
the projected image. (Refer to page 35.)