Technical Data; Unpacking; Attachment / Before Starting The Equipment; Initial Operation - Scheppach HL805 Traduction Du Manuel D'origine

• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Release the handle button and switch off the ma-
chine prior to any operations.
• Avoid accidental starts of the machine: Do not press
the start button while inserting the plug into the socket.
• Use the tools recommended in this manual to ob-
tain the best results from your machine.
• Always keep hands away from the work area when
the machine is running.

7. Technical data

Motor V/Hz 230V / 50Hz 400V / 50Hz
Input P1 W
Output P2 W 2100 W
Operating mode
Motor speed 1/min
Dimensions D/W/H 920 x 690 x 1520 mm
Table height
Working height
Log length
Power max. tons*
Piston stroke
Forward speed 4 cm/s
Return speed 10 cm/s
Oil quantity
Weight 103 kg
Subject to technical changes!

8. Unpacking

Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage. In case of complaints the dealer must be
informed immediately. Subsequent complaints will
not be accepted. If possible, store the packaging until
the warranty period has expired.
Read the operating manual to make yourself familiar
with the device prior to using it.
Only use original parts for accessories as well as for
wearing and spare parts. Spare parts are available
from your specialized dealer.
Specify our part numbers as well as the type and year
of construction of the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
3000 W
2250 W
S6 40%
2800
815 mm
900 mm
550 mm
8
450 mm
4 cm/s
12 cm/s
4 l
101 kg
9. Attachment / Before starting the
equipment
9.1 Fitting the wheels (Fig. 3)
• Insert the bolt (b) through the wheel (7).
• Now insert the bolt through the holes in the lower
part of the splitter.
• Now secure the bolt with a cotter pin
• Repeat this process on the other side.
9.2 Fitting the complete control arms (Fig. 4 + 5)
• Grease the metal plate
• Insert the complete control arm in the position
provided (Fig. 4).
• Guide control arm (10) into the rocker switch (7a)
(Fig. 4)
• Secure the complete control arm with a cylindrical
screw (a), two washers and a self-locking nut.
• Now fasten the other control arm on the other side
in accordance with the method described.
• Attention! Do not clamp the control arms too
tightly, they must move easily.
• Mount the safety bars (G) at the end. These are fitted
on the control arm with two Phillips countersunk-
head screws (Fig. 5)
9.3 Installing the claws + additional retainers (Fig.
6 + 7)
• Fasten the additional retainers (D) together with the
claws (C) on the control arm (Fig. 4)
• To do so, insert two hexagon screws (c) through the
holes on the control arm and secure each with a
self-locking nut (Fig. 7)
• Note that the prongs on the claws must point
towards each other after installation (fig. 9)
9.4 Installing the table and tray tables (Fig. 8 - 10)
• Undo the star-grip screw (8a) (Fig. 8)
• Now fit the table (6) in the retainer intended (Fig.
8) and re-tighten the star grip screws previously
loosened.
• Now hang the tray tables (12) on two screws located
on the side of the table (6) respectively (Fig. 9 + 10)
m IMPORTANT!
You must fully assemble the appliance before using it
for the first time!

10. Initial operation

Make sure the machine is completely and expertly as-
sembled. Check before every use:
• The connection cables for any defective spots
(cracks, cuts etc.).
• The machine for any possible damage.
• The firm seat of all bolts.
• The hydraulic system for leakage.
• The oil level.