Technical Data; Unpacking; Attachment / Before Starting The Equipment - Scheppach HL660o Mode D'emploi

Remaining hazards
The machine has been built using modern tech-
nology in accordance with recognized safety
rules. Some remaining hazards, however, may
still exist.
• The splitting tool can cause injuries to fingers and
hands if the wood is incorrectly guided or support-
ed.
• Thrown pieces can lead to injury if the work piece is
not correctly placed or held.
• Injury through electric current if incorrect electric
connection leads are used.
• Even when all safety measures are taken, some re-
maining hazards which are not yet evident may still
be present.
• Remaining hazards can be minimized by following
the safety instructions as well as the instructions in
the chapter Authorized use and in the entire operat-
ing manual.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Release the handle button and switch off the ma-
chine prior to any operations.
• Avoid accidental starts of the machine: Do not
press the start button while inserting the plug into
the socket.
• Use the tools recommended in this manual to ob-
tain the best results from your machine.
• Always keep hands away from the work area when
the machine is running.

7. Technical data

Dimensions
L x W x H mm
Wood ø max cm
Wood length
max cm
Weight without base frame (kg)
Motor V/Hz
Input P1 W
Output P2 W
Rating
Splitting Power t
Cylinder rise mm
Cylinder speed (fast fwd.) cm/
sec
Cylinder speed (return) cm/sec
Hydraulic fluid capacity l
Operating pressure bar
Motor speed 1/min
Subject to technical changes!
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
1160 x 425 x 610
5 - 25
52
59
230/50
2200
1700
S3 25%
max. 6,5
370
3,08
5,29
3,5
208
2800
Noise
m Warning: Noise can have serious effects on
your health. If the machine noise exceeds 85 dB (A),
please wear suitable hearing protection.

8. Unpacking

Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage.
In case of complaints the dealer must be informed
immediately. Subsequent complaints will not be ac-
cepted.
If possible, store the packaging until the warranty pe-
riod has expired.
Read the operating manual to make yourself familiar
with the device prior to using it.
Only use original parts for accessories as well as for
wearing and spare parts. Spare parts are available
from your specialized dealer.
Specify our part numbers as well as the type and year
of construction of the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
9. Attachment / Before starting the
equipment
At least two people are required to install the
device.
9.1 Installing the handle (4) (enclosed accessories
bag a) (fig. 3)
Fasten the handle to the U-bar with two cylindrical
screws.
9.2 Installing the protective guard (L) (enclosed
accessories bag b) (fig. 4 + 5)
1. Fit the protective guard (L) to the trunk guide plate
(5) and use the enclosed cylindrical screws and
nuts to affix it.
2. Undo the cylindrical screw with washer that is lo-
cated on the wheel bracket.
3. Fasten the other end of the strut to the protective
guard using the Phillips head screw and nut. (3)
4. Now guide the open end of the strut (O) between
the washer and the wheel bracket, tighten the cy-
lindrical screw (4) again firmly.
GB | 21