Technical Data; Unpacking; Attachment / Before Starting The Equipment - Scheppach HL400CH Traduction Des Instructions D'origine

Remaining hazards
The machine has been built using modern tech-
nology in accordance with recognized safety
rules. Some remaining hazards, however, may
still exist.
• The splitting tool can cause injuries to fingers and
hands if the wood is incorrectly guided or supported.
• Thrown pieces can lead to injury if the work piece
is not correctly placed or held.
• Injury through electric current if incorrect electric
connection leads are used.
• Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
• Remaining hazards can be minimized by following
the safety instructions as well as the instructions in
the chapter Authorized use and in the entire oper-
ating manual.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Release the handle button and switch off the ma-
chine prior to any operations.
• Avoid accidental starts of the machine: Do not
press the start button while inserting the plug into
the socket.
• Use the tools recommended in this manual to ob-
tain the best results from your machine.
• Always keep hands away from the work area when
the machine is running.

7. Technical data

Dimensions L x W x H
Wood ø max
Wood length max
Weight
Motor
Input P1
Output P2
Rating
Splitting Power
Cylinder rise
Cylinder speed (fast fwd.)
Cylinder speed (return)
Hydraulic fluid capacity
Operating pressure
Motor speed
Subject to technical changes!
Noise
m WARNING: Noise can have serious effects on
your health. If the machine noise exceeds 85 dB (A),
please wear suitable hearing protection.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
995 x 425 x 610 mm
25 cm
37 cm
45 kg
230/50 V/Hz
1500 W
1100 W
S1
max. 4 t
290 mm
3,86 cm/sec
6,44 cm/sec
2,4 l
165 bar
2850 1/min

8. Unpacking

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• In case of complaints the dealer must be informed
immediately. Subsequent complaints will not be ac-
cepted.
• If possible, store the packaging until the warranty
period has expired.
• Read the operating manual to make yourself famil-
iar with the device prior to using it.
• Only use original parts for accessories as well as
for wearing and spare parts. Spare parts are avail-
able from your specialized dealer.
• Specify our part numbers as well as the type and
year of construction of the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
9. Attachment / Before starting the
equipment
At least two people are required to install the
device.
9.1 Installing the handle (4) (enclosed accesso-
ries bag a) (fig. 3)
Fasten the handle to the U-bar with two cylindrical
screws.
9.2 Installing the protective guard (L) (enclosed
accessories bag b) (fig. 4 + 5)
1. Fit the protective guard (L) to the trunk guide plate
(5) and use the enclosed cylindrical screws and
nuts to affix it.
2. Undo the cylindrical screw with washer that is lo-
cated on the wheel bracket.
3. Fasten the other end of the strut to the protective
guard using the Phillips head screw and nut. (3)
4. Now guide the open end of the strut (O) between
the washer and the wheel bracket, tighten the cy-
lindrical screw (4) again firmly.
9.4 Installing the tray table (K + M) (enclosed ac-
cessories bag c + d + e) (fig. 6 + 7 + 8)
1. Attach the tray table (K) to the same side as the
protective guard (L). Use two cylindrical screws
and spring washers to affix the table to the log
splitter. (1)
GB | 21