Table des Matières
Publicité
Always check that the Lower Contact Arm or Metal Connector Attachment moves freely before using tool. If any binding occurs,
© Stanley Bostitch
repeat assembly procedure or have tool serviced at an authorized Bostitch service center.
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
SEQUENTIAL TRIP - F21PL, F33PT, F28WW, N89RH17-2, N89RH17-2MCN
compliance for the products.
Your new F21PL/F33PT/F28WW/N89RH17-2/N89RH17-2MCN comes fitted with Sequential trip as standard (Grey trigger)
1. This offers positive safety advantages since it will not accidentally drive a nail if the tool is bumped against any surface or
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
anybody while the operator is holding the tool with the trigger pulled.
rien que les produits soient conformes aux normes CE.
2. Allows Place Nailing without the possibility of driving a second nail on recoil.
The sequential trip gets it name from the "sequence" required to operate the tool. To drive a nail, the operator must first depress
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
the trip against he work and then pull the trigger. To drive a second nail, the operator must lift the tool from the work, release the
die CE-Richtlinien für Produkte.
trigger, and the repeat the above sequence.
As accurate placing is required for applying Metal Connectors, and the reasons above the F21PL/N89RH17-2MCN must NOT
be converted to a contact trip model.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
Warning! To avoid serious injury from fasteners and flying debris when installing metal connectors with the
F21PL/N89RH17-2MCN:
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
●
Always use the Metal Connector Attachment. (see installation instructions).
produkterne.
●
Only use sequential trip(grey trigger).
●
Use only genuine Bostitch metal connector nails.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
●
Use only one stick of metal connector nails at a time.
yhdenmukaisuutta.
●
Metal connector nails are not designed to penetrate metal. When installing metal connectors, always place the Metal
Connector Attachment Guide in the metal connector's preformed hole before attempting to drive a fastener. (Fig 3 & 4)
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
TOOL TRIP OPERATION:
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
All tools with a safety trip are marked with an inverted equilateral triangle (▼). Do not attempt to use a tool marked in this
conformità CE per i relativi prodotti.
way if the safety trip is missing or appears damaged.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
SEQUENTIAL TRIP
merking for produktet.
(Reference 2 in Technical Data Table, column L)
The sequential trip requires the operator to hold the tool against the work with the safety trip depressed
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
before pulling the trigger. In order to drive additional fasteners, the trigger must be released and the tool
conformidade com a CE para os produtos.
lifted away from the work, before repeating the above mentioned steps. This makes accurate fastener
placement easier, for instance on framing, toe nailing and crating applications. The sequential trip
allows exact fastener location without the possibility of driving a second fastener on recoil, as described
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
GREY TRIGGER
under Contact Trip (below). The sequential trip tool has a positive safety advantage because it will not
conformidad con las normas CE de los productos.
accidentally drive a fastener if the tool is contacted against the work - or anything else - while the
operator is holding the trigger pulled.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
CONTACT TRIP (SERIAL NUMBER 07315XXX ONWARDS)
(Reference 1 in Technical Data Table, column L)
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
The common operating procedure on "Contact Trip" tools is for the operator to actuate the safety trip
stanowią deklaracji zgodności CE prezentowanych produktów.
while keeping the trigger pulled, thus driving a fastener each time the work is contacted. This will allow
rapid fastener placement on many jobs, such as sheathing, decking and pallet assembly. All pneumatic
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
tools are subject to recoil when driving fasteners. The tool may bounce, releasing the safety trip and if
stanowią deklaracji zgodności CE prezentowanych produktów.
BLACK TRIGGER
unintentionally allowed to re-contact the work surface with the trigger still actuated (finger still holding
the trigger pulled) an unwanted second fastener will be driven.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
These tools are labeled with a "do not use on stairs or ladders" symbol. Technical Data Table Illustration.
výrobky.
Tools marked with this symbol must not be used where changing from one working position to another
involves the use of ladders, stairs or similar structures such as roof laths.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
FASTENER DEPTH CONTROL ADJUSTMENT (FIG 5)
a termék CE-megfelelőségét.
The Fastener Depth Control Adjustment feature provides control of the nail drive depth from flush with or just above the work
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
surface to shallow or deep countersink.
conformitatea CE pentru produse.
Publicité
Table des Matières
