Mains Connection - Güde GRK 210 BS Traduction Du Mode D'emploi D'origine

ENGLISH
26
equipment is functioning properly, in good condi-
tion and in the correct position.
Only use the saw with guards in good working order
and properly maintained, and in position.
When performing mitre, bevel or compound mitre
cuts, adjust the sliding fence to ensure the correct
clearance from the blade.
Do not remove sawing residues or other parts of
workpieces from the sawing area when the machine
is running with an unprotected saw blade and the
saw head is not in its home position.
Never reach into the danger area of the machine
when it is running.
Always use the protective shields on the machine.
Any faults with the machine, including any related to
the safeguard or the saw blades, must be reported to
the persons in charge of safety as soon as the faults
are discovered.
The protective cover should only open when the
machine is lowered to the workpiece.
If necessary, support long workpieces with suitable
additional bases.
Long workpieces must be adequately supported.
Do not use protective equipment to transport or lift.
The handle lock must always be engaged when
transporting the mitre saw.
Connect the saw to a dust-collecting device when
sawing wood.
Replace the worn table insert.
Wear gloves when handling the saw blades and
rough materials.
Ensure that the speed specified on the saw blade is
at least as high as the speed specified on the saw.
Ensure that the workpiece is always clamped secure-
ly to the saw bench.
Inspect before each use.
• Carry out a visual inspection before switching the
appliance on.
• Check especially the safety equipment, electrical
control elements, power lines and screw couplings
for any damage and if they are tightened approp-
riately. If necessary, replace damaged parts before
operation.
• REMOVE ADJUSTING KEYS AND WRENCHES. From
habit of checking to see that keys and adjusting
wrenches are removed from tool before turning
it "ON".
Risk of injury!
Keep body parts and clothes away from rotating
parts of the device.
Use protective equipment which fit you.
Wear a hairnet if you have long hair.
In the event of a blockage, switch off the machine
immediately. Pull out the mains plug and remove the
jammed workpiece.
Chips and splinters must not be removed while the
machine is running.

Mains Connection

Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
Connect only to single-phase AC system voltage as
indicated on the rating plate. It is also possible to
connect to sockets without an earthing contact as
the design conforms to safety class II. Only plug-in
when machine is switched off.
The machine meets the EN 61000-3-11 requirements
and is subject to special connection conditions.That
means that a use on optional points of connection
is not allowed.The machine may cause temporary
voltage fluctuation in adverse conditions.
The machine has only been designed to be used on
points of connection not exceeding the maximum
allowable network impedance Zmax = 0.233 Ω.
As a user, you must make sure, after consultation
with your energy provider, if necessary, that your
point of connection on which the machine is to be
operated meets the requirements above.
Laser
Do not stare into beam. Do not point laser light at
other persons.
Do not view directly into beam with optical instru-
ments (binocular, telescope).
Do not point laser at reflective surfaces.
Avoid exposure to laser radiation. Laser may emit
hazardous radiation.
Do not replace the integral laser with a different
type.
Any repairs must only be carried out by the autho-
rized service agent.
Maintenance
Unplug the machine before any work on it.
Carry out a visual inspection before switching the
appliance on.
The appliance must not be used if damaged or safety
equipment is defective. Replace any worn-out and
damaged parts.
Caution! If the power cord of the appliance gets
damaged, it must be replaced by the manufacturer
or its customer service or a similarly qualified person
to avoid danger.
Repairs and works specified in these Instructions may
only be performed by qualified authorised staff.
Use only original accessories and original spare parts.