Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
D711_IFU_EN_for_EU.book Page 17 Friday, August 24, 2007 3:58 PM
Set a number to be barred
m
d
1. Press
, scroll
to
ADVANCED SET
and press
d
m
2. Scroll
to
CALL
BARRING. Press
.
3. Enter the master PIN (default setting 0000) and press
d
m
4. Scroll
to NUMBER. Press
.
u
d
5. If necessary, scroll
or
to the next available slot.
m
6. Press
and enter the number or prefix you want to bar. Press
to confirm.
>
7. Press
to return to standby.
Baby call
When activated, this feature allows you to dial a number by pressing any key on your handset
>
(except
). This feature is very useful for access to emergency services.
Switch baby call on/off
m
d
1. Press
, scroll
to
ADVANCED SET
and press
d
m
2. Scroll
to
BABY
CALL. Press
.
3. Enter the master PIN (default setting 0000) and press
m
u
4.
MODE
is displayed. Press
then press
or
>
5. Press
to return to standby.
NOTE
If you switch Baby call on,
BABY CALL ON
will be displayed on your screen in standby mode.
To switch Baby call off again:
>
1. Press
.
m
2.
OFF?
is displayed. Press
to confirm.
Set the baby call number
m
d
1. Press
, scroll
to
ADVANCED SET
and press
d
m
2. Scroll
to
BABY
CALL. Press
.
3. Enter the master PIN (Default setting 0000) and press
d
m
4. Scroll
to NUMBER. Press
.
m
5. Enter the number. Press
to confirm
>
6. Press
to return to standby.
Dial a baby number
1. When a baby call number has been stored and the baby call setting switched on, press any
>
key (apart from
), to dial a number.
NOTE
When baby call is switched on, you can still answer any incoming call as normal.
Registration
Up to 5 handsets can be registered to one base station. Additional handsets must be registered
to the base before you can use them.
• The instructions described below apply specifically to your D711 handset. If you wish to
register another manufacturer's handset, the instructions may vary. In this case, please refer to
the manufacturer of the additional handset.
Advanced settings
• The Master PIN is required before you can register or unregister handsets. The default PIN is
m
.
Register a handset
m
.
At the base:
1. Press and hold the
m
At the handset:
1. Press
2. Scroll
3. If necessary, scroll
m
.
m
4. When the display shows PIN----, enter the base PIN.
.
d
m
to select
ON
or OFF. Press
to confirm.
Select a base
You can register your D711 handset with up to 4 bases. Once registered, you can switch between
bases, for example, bases at home and at work.
1. Press
2. Scroll
3.
m
4. Enter the number of the base you want – 1,2,3 or 4 and press
.
m
.
Unregister a handset
1. Press
2. Scroll
3. Enter the 4 digit master PIN and press
4. Scroll
PIN
The 4-digit master PIN is used when registering or unregistering a handset and when changing
some settings on your D711. The default setting is 0000. You can change this PIN for more
security.
1. Press
2. Scroll
3. Enter the current 4 digit master PIN and press
4. Enter the new PIN and press
0000.
p
button on the base station for at least 3 seconds. The base station
emits a beep when it is ready to accept registration. You have 90 seconds in which to register
a handset.
m
d
m
and scroll
to
ADVANCED SET
and press
.
d
m
to
REGISTRATION
and press
.
u
d
or
to display
REGIST. BASE
and press
the registered base number is flashing. Enter the number of the base on which you wish to
register your handset.
1
If you have only 1 base station, press
. If you have 2 base stations, press
-
When the handset registers with the base, it is assigned a handset number.
m
d
m
and scroll
to
ADVANCED SET
and press
.
d
m
to
REGISTRATION
and press
.
m
SELECT BASE
is displayed. Press
.
-
The available bases are displayed with the current base number flashing.
-
When the base is found you hear a beep. If not found, the display shows UNREGISTERED.
m
d
m
and scroll
to
ADVANCED SET
and press
.
d
m
to
UNREGISTER
and press
.
m
.
-
Display shows the registered handset numbers.
u
d
or
to select the handset you want to delete and press
-
UNREGISTERED
is displayed on the handset screen.
m
d
m
, scroll
to
ADVANCED SET
and press
.
d
m
to PIN. Press
.
m
. (Default setting 0000)
m
.
m
.
BASE 1 2 3 4
is displayed and
1
2
or
, etc.
m
.
m
.
17
Publicité
Chapitres
Table des Matières
