Maintenance; The Importance Of Maintenance; Maintenance Safety - Honda HRS536SDE Manuel De L'utilisateur

Blade Speed
The blade must spin very fast to cut properly. Always use the fast
throttle setting, and keep the engine running at maximum rpm.
If engine speed drops, it could mean the engine is being overloaded
by the blade trying to cut too much grass. Mow a narrower swath,
move the mower slower, or raise the cutting height.
Blade Sharpness
A sharp blade cuts cleanly. A dull blade tears the grass, leaving
shredded ends that turn brown. When your blade doesn't cut cleanly
anymore, have it sharpened or replaced.
Dry Grass
If the ground is too dry, mowing will stir up a lot of dust. Besides being
unpleasant to work in, too much dust will clog the carburetor air filter.
If dust is a problem, water your lawn the day before mowing. Mow
when the grass is dry to your touch, but the soil is still moist.
Wet Grass
Wet grass is slippery and can make you lose your footing. Also, wet
grass clippings will clog the mower deck and collect in clumps on the
lawn. Always wait for wet grass to dry before mowing.
Fallen Leaves
If you want to mulch fallen leaves into your lawn, don't let the leaf
cover get too deep before you begin. For best results, start mulching
while grass still shows through the leaf cover. In places where fallen
leaves completely cover the grass, remove the leaves by raking.
Clogged Mower Deck
Before clearing a clogged mower deck, stop the engine and turn the
fuel valve to the OFF position. With the spark plug cap disconnected,
tilt the mower so the air cleaner side is up.
Clear a clogged deck with a stick, not your hands.
Mowing Patterns
Your Honda mower will work most efficiently if you use the following
mowing pattern as much as possible. Mower deck and equipment
design and the direction in which the blade rotates causes this
mowing pattern to give the best results.
Mulching
Use a counterclockwise mowing
pattern. If the lawn has an irregular
shape, or many obstacles, divide it
into sections where you can use
counterclockwise mowing patterns.
Side Discharge Mowing
Where possible, use the same
mowing pattern recommended for
mulching. If the lawn has an irregular
shape or many obstacles, divide it
into sections where clippings will be
discharged away from uncut areas.
This will prevent clippings from piling
up in the path of the mower.
10
MULCHING AND SIDE
DISCHARGE PATTERN
ENGLISH

MAINTENANCE

THE IMPORTANCE OF MAINTENANCE

Good maintenance is essential for safe, economical, and trouble-free
operation. It will also help reduce air pollution.
To help you properly care for your mower, the following pages include
a maintenance schedule, routine inspection procedures, and simple
maintenance procedures using basic hand tools. Other service tasks
that are more difficult, or require special tools, are best handled by
professionals and are normally performed by a Honda technician or
other qualified mechanic.
The maintenance schedule applies to normal operating conditions. If
you operate your mower under unusual conditions, consult an
authorized Honda dealer for recommendations applicable to your
individual needs and use.
Remember that your Honda dealer knows your mower best and is
fully equipped to maintain and repair it.
To ensure the best quality and reliability, use only new, Honda
Genuine parts or their equivalents for repair and replacement.

Improper maintenance, or failure to correct a problem
before operation, can cause a malfunction in which you
can be seriously hurt or killed.
Always follow the inspection and maintenance
recommendations and schedules in this owner's
manual.

MAINTENANCE SAFETY

Some of the most important safety precautions follow. However, we
cannot warn you of every conceivable hazard that can arise in
performing maintenance. Only you can decide whether or not you
should perform a given task.

Failure to properly follow maintenance instructions and
precautions can cause you to be seriously hurt or
killed.
Always follow the procedures and precautions in this
owner's manual.
Safety Precautions
• Make sure the engine is off before you begin any maintenance or
repairs. This will eliminate several potential hazards:
– Carbon monoxide poisoning from engine exhaust.
Be sure there is adequate ventilation whenever you operate the
engine.
– Burns from hot parts.
Let the engine and exhaust system cool before touching.
– Injury from moving parts.
Do not run the engine unless instructed to do so.
• Read the instructions before you begin, and make sure you have
the tools and skills required.
• To reduce the possibility of fire or explosion, be careful when work-
ing around gasoline. Use only a nonflammable solvent, not gaso-
line, to clean parts. Keep cigarettes, sparks, and flames away from
all fuel-related parts.
WARNING
WARNING