Guida Rapida - Migatronic OMEGA 3 YARD BASIC Guide Rapide

Tabella parametri di saldatura (set value)
Processo 1,0 mm
Materiale Filo Gas S U0
(m/min) (V)
Fe 0,8 CO 2,5 19,0
2
Fe 1,0 CO 2,0 18,0
2
Fe 1,2 CO 1,0 18,0
2
Fe 0,8 ArCO 3,0 16,0
2
Fe 1,0 ArCO 2,0 15,0
2
Fe 1,2 ArCO 1,5 16,5
2
Fe 1,6 ArCO
2
CrNi 1,0 ArCO 3,0 15,0
2
CrNi 1,2 ArCO 2,0 15,0
2
AI 1,0 Ar 4,0 14,5
AI 1,2 Ar 3,5 13,0
Processo 4,0 mm
Materiale Filo Gas S U0
(m/min) (V)
Fe 0,8 CO 13,0 29,0
2
Fe 1,0 CO 6,0 22,5
2
Fe 1,2 CO 4,5 23,0
2
Fe 0,8 ArCO 14,0 26,0
2
Fe 1,0 ArCO 8,0 20,0
2
Fe 1,2 ArCO 5,5 20,5
2
Fe 1,6 ArCO 3,0 19,5
2
FeFlux 1,2 ArCO 6,0 21,0
2
CrNi 1,0 ArCO 9,0 25,0
2
CrNi 1,2 ArCO 8,0 24,0
2
AI 1,0 Ar 11,0 22,0
AI 1,2 Ar 10,0 18,0
1,5 mm 2,0 mm 3,0 mm
S U0 S U0 S
(m/min) (V) (m/min) (V) (m/min)
4,5 19,5 7,0 21,0 11,0
2,5 19,0 3,0 20,0 4,5
2,0 20,0 2,5 21,0 3,5
6,0 18,0 7,5 19,5 11,0
3,0 16,0 4,0 17,0 6,0
2,5 17,5 3,5 18,0 4,5
1,0 17,0 2,0 18,0 2,5
4,0 16,0 6,0 17,0 8,5
3,0 16,0 3,5 16,5 6,0
6,0 15,0 7,5 16,0 9,0
5,0 15,0 8,0 16,0 9,0
6,0 mm 10,0 mm
S U0 S U0
(m/min) (V) (m/min) (V)
18,0 30,0 24,0 37,0
9,0 24,5 14,0 32,0
7,5 28,5 11,0 36,0
18,0 31,0 24,0 33,0
11,5 26,5 16,0 30,0
8,0 29,0 10,0 32,0
4,0 22,0 5,5 29,0
8,0 25,0 11,0 28,0
10,0 27,0
10,0 24,0 12,0 31,0
13,0 25,0 15,0 27,0
13,0 23,0 15,0 26,0
Tabella 1
Regolazione del processo di saldatura
Tenere premuta la manopola (11A) per aprire il menù dei parametri secondari.
Selezionare il parametro girando la manopola (10) e regolarlo girando la manopola (11).
Per chiudere il menù premere brevemente (11A).
U0
Premere per breve tempo (12) per attivare la visualizzazione di Fxx (F = function) nomi parametri
(V)
on/off.
27,0
21,0
22,0
Parametri MIG/MAG
20,0
19,0
A
20,5
18,5
20,0
18,0
19,0
m/min
17,0
t1
S
GS.F / F22 (gas flow) 0,5-27 l/min (solo macchine con IGC) (kit opzionale)
Parametri MMA
Quando si sia impostato il programma MMA sono
selezionabili solo i seguenti parametri :
A
t
Corrente di
saldatura (A)
Figura 1

GUIDA RAPIDA

OMEGA
3
Corrente di saldatura (A)
Pr.G / F31 Pre-gas
S.St / F32 Soft start
bb.t / F37 Burn-Back
Po.G / F38 Post-gas
SP.t / F39 Tempo puntatura/Spot time
t
t2
S
S
t
HS.A / F11 Hotstart (25%)
HS.t / F12 Tempo di Hotstart (0,5 sec.)
Arc / F13 Arc force (25%)
Corto circuito
t
YARD BASIC
(0,2 sec.)
(1,0 m/min.)
(5 (0-30))
(3,0 sec.)
(0,0 sec.)
IT 50113783 A