Product Maintenance; Product Disposal; Technical Characteristics Of The Product - Nice Moon MC824H Instructions Et Avertissements Pour L'installation Et L'utilisation

8

PRODUCT MAINTENANCE

Regular maintenance is needed to keep the level of safety constant and to
ensure the maximum durability of the entire automation .
Maintenance must be performed in strict accordance with the safety provi-
sions set out in this manual and with the requirements of applicable laws and
standards .
Important – During maintenance and cleaning the control unit must be discon-
nected from the electrical power supply .
For devices other than the MC824H follow the instructions given in the relevant
maintenance programmes .
For the MC824H scheduled maintenance must be performed no more than 6
months or 20,000 manoeuvres after previous maintenance .
To perform maintenance, proceed as follows:
01. Disconnect all electric power sources, including any buffer batteries;
02. Check all materials making up the control unit for wear, with particular
attention to erosion or oxidation of parts; replace parts that are not in opti-
mal condition;
03. Reconnect the power supply and perform the checks described in chapter
4 .1 - Testing .
WARNINGS: • All technical characteristics stated refer to an ambient temperature of 20°C (±5°C). • Nice S.p.a reserves the right to modify the product at any time while maintaining
the same functionalities and intended use .
MC824H power supply
MC824H/V1 power supply
Nominal power absorbed from mains
Power absorbed by control unit battery
connector with "standby-All" operation
(including a receiver with SM type connector)
Flashing light output [*]
Electric lock output [*]
Gate open light output [*]
BLUEBUS output
STOP Input
PP Input
OPEN Input
CLOSE Input
Radio connector
Radio AERIAL input
Programmable functions
Functions in self-learning mode
Operating temperature
Use in particularly acid, saline or
potentially explosive atmospheres
Protection rating
Dimensions (mm)
Weight (kg)
[*] The Flashing Light, Electric Lock and Gate Open Warning light outputs can be programmed with other functions (see "TABLE 5 - 1st level functions"; or via Oview programmer, see
chapter 7 .2) . The electrical characteristics of the output vary according to programming:
flashing light: 12Vdc, 21 Wmax lamp
electric lock: 12Vac 15 VAmax
other outputs (all types): 1 lamp or relay 24Vdc (-30 and +50%), 4 Wmax
10 – English

TECHNICAL CHARACTERISTICS OF THE PRODUCT

230 Vac (+10% -15%) 50/60 Hz
120 Vac (+10% -15%) 50/60 Hz
200 W
below 100 mW
1 "LUCYB" type flashing light (12 V, 21 W lamp)
1 max . 12 Vac max . 15 VA electric lock
one 24 V max . 4 W lamp (output voltage may vary between -30% and +50%, output may also control small relays)
1 output with maximum load 15 Bluebus units (maximum 6 pairs of MOFB or MOFOB photocells + 2 pairs of MOFB or MOFOB
photocells assigned as Opening devices + max . 4 MOMB or MOTB control devices
For normally closed, normally open or 8 .2 kΩ constant resistance contacts in self-learning mode (a change from the memorised
state prompts the "STOP" command)
for normally open contacts (closure of the contact prompts the Step by Step command)
for normally open contacts (closure of the contact prompts the OPEN command)
for normally open contacts (closure of the contact prompts the CLOSE command)
SM connector for SMXI, OXI and OXIFM family receivers
50 Ω for RG58 or similar type cable
8 ON-OFF type functions and 8 adjustable functions
• Self-learning of devices connected to the BlueBus output
• Self-learning of type of device connected to "STOP" terminal (NO, NC or 8 .2 kΩ resistance contact)
• Self-learning of leaf travel and automatic calculation of deceleration and partial opening points (vary according to installation)
from - 20 °C a + 50 °C
NO
IP 54 with enclosure intact
310 x 232 x H 122
4,1

PRODUCT DISPOSAL

This product is an integral part of the automation system it controls
and must be disposed of along with it.
As in the case of installation, likewise at the end of product lifetime the disas-
sembly and scrapping operations must be performed by qualified personnel.
This product is made of various types of material, some of which can be recycled
while others must be scrapped . Seek information on the recycling and disposal
methods envisaged by the local regulations in your area for this product category .
Important! – Some parts of the product may contain polluting or hazardous
substances which, if released to the environment, may cause serious damage
to the environment or to human health .
As indicated by the symbol alongside, disposal of this product
with domestic waste is strictly prohibited . Separate the waste into
categories for disposal, according to the methods established by
current legislation in your area, or return the product to the retailer
when purchasing a new version .
Important! – Local legislation may impose heavy fines in the
event of illegal disposal of this product .
Disposal of buffer battery (if present)
Important! – Even if discharged, the batteries may contain pollutant substanc-
es and therefore must NEVER be disposed of in normal waste collection points .
Dispose of according to separate waste collection methods as envisaged by
current local standards .