Noise/Vibration Information; Declaration Of Conformity - Würth master HKS 55 Combi Notice D'utilisation

HKS 55.book Seite 17 Dienstag, 14. Oktober 2008 10:22 10
Uncoated saw blades can be protected from corro-
sion with a thin coat of acid-free oil. Remove the oil
again before use to prevent spotting of wood.
Resin and glue residue on the saw blade cause poor
cutting results. Therefore, clean the saw blade imme-
diately after use.
If the machine should fail despite the care taken in
manufacturing and testing, repair should be carried
out by a Würth Master-Service agent.
For all correspondence and spare parts orders, al-
ways include the article number on the type plate of
the machine.
For the current spare parts list of this machine, log
into the Internet under "http://www.wuerth.com/
partsmanager" or ask for a copy at your nearest
Würth branch office.
Disposal
Power tools, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into
household waste!
According to the European Directive
2002/96/EC on waste electrical
and electronic equipment and its
incorporation into national law, power tools that are
no longer suitable for use must be separately col-
lected and sent for recovery in an environmental-
friendly manner.
Warranty
For this Würth tool, we provide a warranty in ac-
cordance with statutory/country-specific regulations
from the date of purchase (proof of purchase by in-
voice or delivery note). Damage that has occurred
will be corrected by replacement or repair.
Damage caused by normal wear, overloading or
improper handling is excluded from the warranty.
Claims can only be accepted if the power tool is sent
undisassembled to a Würth branch office, your
Würth sales representative or a customer service
agent for Würth compressed-air and power tools.

Noise/Vibration Information

Measured
EN 60 745.
Typically the A-weighted noise levels of the machine
are:
Sound pressure level: L
Sound power level: L
Wear hearing protection!
Overall vibrational values (vector sum of three direc-
tions) determined according to EN 60 745:
Vibrational emission value a
tainty K =1.5 m/s
h,D
Dhe vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of the vibrational
impact.
The declared vibration emission level represents the
main applications of the power tool. However if the
power tool is used for other applications, with differ-
ent accessories or poorly maintained, the vibration
emission may differ. This may significantly increase
the vibrational impact over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the ex-
posure level over the total working period.
Identify additional safety measures to protect the op-
erator from the effects of vibration such as: Maintain
the power tool and the accessories, keep the hands
warm, organisation of work patterns.

Declaration of Conformity

We declare under our sole responsibility that this
product is in conformity with the following standards
or standardization documents:
EN 60 745 according to the provisions of the regu-
lations 98/37/EG (->28.12.09), 2006/42/EG
(29.12.09->), 2004/108/EG.
08
Adolf Würth GmbH & Co. KG
P. Zürn
Subject to change without notice
values determined according
/K dB (A) 94/3;
pA pA
/K dB (A) 105/3.
WA WA
=3.0 m/s
h,D
2
.
A. Kräutle
to
2
, Uncer-
17