Safety Messages; Maintenance And Care; Storage And Disposal - SLV 228331 Mode D'emploi

ENGLISH
OPERATING MANUAL FOR
RECESSED GROUND LUMINAIRE
POWER TRAIL-LITE
Read this short manual carefully and keep it accessible for further
reference!

SAFETY MESSAGES

Disregard of the safety messages may lead to danger of life, burning or
fire!
 Installation, mounting or works on the electrical connection may only be
carried out by an approved electrician.
 Type Y attachement: If the external flexible cable or cord of this luminaire is
damaged, it shall be exclusively replaced by the manufacturer or a
qualified electrician.
 Do not look directly into the light source.
 The product may not be modified or converted.
 Do not hang or fasten anything on the product, especially no decoration.
 Do not cover the product - provide free air circulation.
 The luminaire may only be operated with a complete and intact protection
glass.
 In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
A malfunction exists when:
 visible damages appear.
 the product does not work properly (e.g. flickering).
 smoke, steam or crackling sounds appear.
 smell of burning is recognisable.
 an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
 This product is not intended to be used by children. Ensure that children do
not suffer any harm e.g. by burns from hot surfaces or by electrical shock.
Additional safety messages are indicated by this symbol:
USE AS DIRECTED
This product serves exclusively lighting purposes and may:
 only be operated using a suitable driver (350mA) (i.e. SLV art.-no.
464108).
 only be installed according to safety class III (three).
 only be operated when firmly mounted on a stable, even and tilt-fixed
surface.
 only be operated on normally or not flammable surfaces.
 not be exposed to strong mechanical loads or to strong contamination.

MAINTENANCE AND CARE

Light source
 The light source of this luminaire may only be replaced by the manufacturer,
an authorized service technician or a comparable qualified person.
Care
 The following enviromental influences may have unwanted effects on the
surface of the product:
 acid rain and sour soil, high salt content in the air
 cleaning agents, fertilizer especially in flowerbeds
 thawing salt, other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface.
Disconnect the product from the power supply and let it cool down, before
you clean the product.
 Clean the product on a regular basis using a slightly moistened, soft and fluff-
free cloth. Please also note additional supplied notes on maintanance and
care.

STORAGE AND DISPOSAL

Storage
 The product must be stored in a dry and clean environment. Do not strain
the product mechanically during storage.
After a damp or soiling storage the product may only be installed after
checking its condition by an approved electrician.
Disposal (European Union)
 Do not dispose the product with the regular household waste! Products
marked with this sign must be disposed according to the directive (WEEE,
2012/19) on electrical and electronic devices at local collection points for such
devices!
INSTALLATION
(only by an approved electrician)
Unpacking
 Carefully take the product out of the packaging removing any transport
safeguards.
.
 Before disposal of the packaging material make sure that all components of
the product are removed.
Installation place
 The product is solely suited for recessed wall and floor installation.
 LED react sensitive on high temperatures! Before installation pay attention to
the expected temperature at the place of operation. This may not exceed the
allowed ambient temperature (ta=40°C) of the product.
Note that maintaining the IP class 67 requires an appropriate connection
corresponding with this IP class.
IP67: Protection against dust (dust-tight) - Protection against the penetration of
water when temporarily submerged.
Prepare the power supply lead according to valid rules for outdoor
installations.
Do not seal the product yourself, using additional silicon or another sealant.
Before installation
 Carry out the installation when the weather is dry.
Installation steps (read completely before installation)
 Prepare the recess if not done yet. When installing the lighting unit
outdoors provide a gravel bed, 20 cm thick, beneath the installation pot.
This serves as protection from corrosion.
 Install the luminaire as shown in the figure.
 Attention: Keep the whole installation off power until the work is completely
finished. A connection with the power on will destroy the LED.
 Electrical Connection
 Prepare the power supply. Use a suitable driver(350mA) i.e. art.-no.
464108.
 If several luminaires are operated on one converter they must be
connected in series.
 Establish the connection as shown in the schematic drawing 1.
a: Luminaire e: Blank tube
b: Installation pot f: Cast-resin sleeve or
watertight connection unit
c: Connection lead of the fitting g: Power supply lead
d: Shrinking tube h: Drainage
 All connections must be properly protected and sealed against
penetration of water and dirt!
Check if the product functions properly and is securely fixed!
art.-no. 228331/32/37/41/42 © 05.04.2016 SLV GmbH,
Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany,
Tel. +49 (0)2451 4833-0
Technical Details are subject to change.