Storing Preset Stations In The Dab Radio Mode; Recalling A Preset Station In The Dab Radio Mode; Listening To Fm Radio; Tuning Into Fm Stations - PERFECTPRO NETBOX Mode D'emploi

Storing preset stations in the DAB radio
mode
The NETBOX features 40 memory presets for DAB radio.
1. Turn on the radio, select the DAB mode and then tune
to the required radio station as previously described.
2. Press and hold the Presets button. The display will
show the "Save to Preset" screen.
3. Rotate the Tuning knob to select the required Preset
number. Then press the Tuning knob to store the preset
station. "Preset stored" will be shown on the display
indicating the station is stored under the selected preset
number. If another station has already been stored
under the chosen preset number, that station will be
overwritten.
4. Alternatively, you can also press and hold one of the
radio's Preset button (1-5) to store the station under the
corresponding Preset number.
5.
Repeat this procedure as needed for the remaining
presets.
Recalling a preset station in the DAB radio
mode
1. Turn on the radio and then select the DAB radio mode
using the Source button or the radio's Main menu.
2. Press the Presets button to display the "Recall from
Preset" screen.
3. Select a preset number by rotating the Tuning knob
and press the Tuning knob to confirm your choice. The
radio will now tune into the selected preset. The chosen
preset number is also shown in the bottom bar of the
radio's display.
4. Alternatively, you can also press one of the Radio's
Preset buttons (1-5) to recall the corresponding preset
number.

9. Listening to FM radio

Tuning into FM stations

To tune into FM radio stations, follow these steps:
1. Turn on the radio using the Power button.
2. Select the FM radio mode by repeatedly pressing the
Source button or using the radio's Main menu.
3. Rotate the Tuning knob clockwise or anti-clockwise
and then press and hold it to automatically tune
into an FM station with a higher or lower frequency
respectively. Your radio will stop scanning when it finds
a station of sufficient strength. The display will show
the frequency of the signal which has been found and
a signal strength icon will be shown in the bottom bar
of the radio's display to indicate the strength of the
signal received. If RDS information is available, an RDS
icon will also be shown in the bottom bar of the radio's
display and after a few seconds the display will show
the radio station name.
4. Rotate the Tuning knob to fine-tune the frequency with
steps of 0.05MHz if needed.
5. Repeat the steps 3 and 4 to tune into other radio
stations.
Note:
Before selecting the FM radio mode and tuning into
stations, make sure the DAB / FM antenna at the back
of the radio has been positioned upright.

The FM radio menu

You can open the FM radio
menu by pressing and holding
the Info / Menu button while the
radio is in the FM radio mode.
The FM radio menu offers the
following options:
● [Scan setting]: Select this
option to configure if the radio should only look for
strong signals or all signals when using the automatic
tuning feature (by pressing and holding the Tuning
knob).
● [System settings]: Select this option to go to the
System settings menu and configure the radio (refer
to chapter 14 "Using the System settings menu" for
details).
● [Main menu]: Select this option to go back to the
Main menu, where you can switch to any of the radio's
modes or set the radio's alarms or sleep timer, or go to
the System settings menu (refer to chapter 15 "Using
the Main menu" for details).

Showing FM information on the display

When listening to a FM radio station that is also
broadcasting RDS data (the RDS icon is shown in the
bottom bar of the radio's display), repeatedly press
the Info / Menu button to cycle through the following
information on the radio's display:
● Text message
● Program type
● Frequency
● Today's Date
If no RDS information is available, the radio will only be
able to show Today's Date.
Storing and recalling preset stations in the
FM radio mode
The NETBOX features 40 memory presets for FM radio.
After selecting the FM radio mode, the procedure for

storing and recalling preset stations in the FM radio mode

is identical to the procedure in the DAB radio mode.
Please refer to the instruction in the previous chapter for
details on how to store and recall preset stations.
FM
Scan setting
>
System settings
Main menu
>
GB
11