Fm Mode; Operating Fm; Manual Tuning; Rds Station Service - PERFECTPRO ROCKBULL Mode D'emploi

FM MODE

Operating FM

1. Press the ON/OFF button to turn on the radio.
2. Select the FM waveband by pressing the SOURCE button.
3. If this is the first time to switch to FM mode, the station in preset 1 will be played.
If the radio has been used before, the last listened station will be played.
4. To seek station, press the TUNING control. The scan stops automatically when it
finds a station of sufficient strength.
5. After a few seconds, the display will update with station name if RDS information is
being received.
6. To find other stations, press the TUNING control again.
7. To seek station in an opposite direction, rotate the TUNING control clockwise (to
scan from low frequency to high frequency) or rotate anti-clockwise (to scan from
high frequency to low frequency), and press the TUNING control.
8. When the waveband end is reached, the radio will recommence tuning from the
opposite waveband end.

Manual tuning

1. Press the ON/OFF button to turn on the radio.
2. Select the FM band by pressing the SOURCE button.
3. Rotate the TUNING control to reach the required FM station.
The radio will change the frequency in steps of 50 kHz.
4. Rotate the rubber antenna to get the best reception. If the radio is tuned to a station
of sufficient signal strength with RDS information present, the display may change
to show the station name.
5. When the waveband end is reached, the radio will recommence tuning from the
opposite waveband end.

RDS station service

RDS (Radio Data System) is an information system which inaudible digital information is
transmitted in addition to the normal FM radio programme. When the radio is receiving a
RDS station and the reception strength is sufficient, the station name will appear in the
display. It may take some time before the RDS information is available.
Calling up RDS information
When you are listening to a FM station with RDS system, repeatedly press the INFO
button to cycle through the information. This will only function if the reception level is
sufficient and clear.
a. Radio text (RT) Displays the message about the station being listened to as
ticker text.
b. Program type (PTY) Displays the type of station being listened to, e.g. Pop,
Classic, News, etc.
c. Frequency Displays the frequency of the station being listened to.
d. Time & date Displays the current time (24 hour clock) and date.
11

Scan sensitivity setting

The radio will normally scan all stations from FM broadcasts including the weaker
signals. However, you may wish the Auto-scan to find only those stations with strong
enough signals to give good reception.
1. Press the ON/OFF button to turn on the radio.
2. Select the FM band by pressing the SOURCE button.
3. Press the MENU button, rotate the TUNING control to "Scan setting".
4. Press the TUNING control.
5. Rotate the TUNING control to select between "All stations" or "Strong station"
(default is All stations).
The "Strong station" option will allow the radio to find strong signals only when
scanning.
6. Press the TUNING control to confirm your setting. The display will return to FM
menu.

PRESET STATIONS

Storing preset stations

There are 20 memory presets in the radio, 10 for DAB and 10 for FM. Presets are
remembered by the radio in the event of a power failure.
1. Press the ON/OFF button to turn on the radio.
2. Press the SOURCE button to select the desired waveband.
3. Tune to the required station.
4. Press and hold the required PRESET button until the radio shows "Saved to
preset".
5. Repeat step 3 and 4 for the remaining presets.
6. Stations stored in the preset memories can be over-written by following the above
procedure.

Recalling preset stations

1. Press the ON/OFF button to turn on the radio.
2. Press the SOURCE button to select the desired waveband.
3. Briefly Press the required PRESET button, the display will show, e.g. "P1", in the
bottom side of the display.
GB
GB
12