SOMFY Sunea 40 RTS DC Notice Originale page 19

2. 3. 7. « Closing force » function
This function allows the closing force of the awning to be increased or decreased to 3 levels
(high/medium/low).
Contact the awning's manufacturer before using these functions to check the compatibility
of your systems.
For safety reasons, this function can only be accessed via the individual control point in 3
situations:
‡ $IWHU WKH VHWWLQJV FRQ¿UPDWLRQ DQG EHIRUH SURJUDPPLQJ WKH ¿UVW FRQWURO SRLQW
‡ $IWHU SURJUDPPLQJ WKH ¿UVW FRQWURO DQG GXULQJ WKH QH[W  F\FOHV
‡ $IWHU D VLQJOH SRZHU RXWDJH DQG GXULQJ WKH QH[W  F\FOHV
Position the motor to the halfway position using the
1)
Down or "Up" button. Press the "My" button to stop
the awning.
To activate closing force function press twice
2)
successively: For half a second press simultaneously
"My" and "Up" buttons, without the motor rotating.
For more than 5 seconds press simultaneously
"My" and "Up" buttons, until the motor jogs.
The motor is now in programming mode for only 10
seconds, the motor is factory set at the medium level.
To increase the closing force, press the "Up" button
3)
until the awning makes a slow movement, the cassette
awning's closing force has moved up a level. To
decrease the closing force, press the "Down" button
until the store makes a slow movement, the cassette
awning's closing force has moved down a level.
&RQ¿UP WKH QHZ VHWWLQJ E\ SUHVVLQJ  VHFRQGV WKH
4)
"My" button, until the motor jogs.
The new setting is memorized.
2. 3. 8. Cancelling the programming
Switch off the 12 V power supply to the motor for
1)
2 seconds.
Switch the 12V power to the motor back on for
2)
7 seconds.
Switch off the 12V power supply to the motor for
3)
2 seconds.
Switch the power to the motor back on.
4)
If the motor is on the end limit position (up or down),
the motor jogs, otherwise, the motor runs for
5 seconds in random direction.
The motor is now in the "cancelling" mode.
If you switch off the power to several motors, they will all be in cancelling mode. You must
"cancel" out of this mode all the motors which you do not want to reset by sending a
command from their individual control transmitter (up or down).
7KHQ FRQ¿UP WKH FDQFHOOLQJ RI WKH FRQFHUQHG PRWRU IURP WKH LQGLYLGXDO FRQWURO
Press the "Prog." button of the transmitter more than
 VHFRQGV 0DLQWDLQ WKH SUHVVXUH XQWLO WKH PRWRU ZLOO ¿UVW
run for a half a second in one direction and then the other,
and a few second later, it will run again in both directions.
The operation is completed.
The motor returns to its initial settings. All transmitters and motor settings are deleted
and reprogramming is required.
Copyright © 2014 Somfy SAS. All rights reserved.
1)
2)
0.5 s
4)
1)
3)
Images are not contractually binding.
3)
5 s
2)
ON
OFF
2 s.
12V
4)
OFF
ON
2 s.
2 s.
7 s.
7 s.
7