Parts & Specs; Assembly Preparation; Mounting The Wheels To The Legs; Assembling The Cart - Pit Boss PB700S Instructions

PARTS & SPECS
Part# Description
1 Porcelain-Coated Steel Upper Cooking Rack
2 Porcelain-Coated Cast-Iron Cooking Grids (x2)
3 Lid Stopper
4 Flame Broiler Slider
5 Flame Broiler Main Plate
6 Main Barrel & Hopper Assembly
7 Lid Handle Bezel (x2)
8 Lid Handle
9 Bottle Opener
10 Grease Tray
11 Side Shelf
12 Tool Hook (x4)
13 Side Shelf Handle
14 Support Leg (x4)
15 Locking Caster Wheel (x2)
16 Bottom Shelf
A Screw (x24)
B Washer (x24)
C Locking Washer (x24)
NOTE: Due to ongoing product development, parts are subject to change without notice. Contact
Customer Service if parts are missing when assembling the unit.
PB – ELECTRIC REQUIREMENTS
110-120V, 3.3AMP, 60HZ, 275W, 3-PRONG GROUNDED PLUG
MODEL UNIT ASSEMBLED (WxHxD) UNIT WEIGHT
1,339mm x 1,112mm x 678mm 59.5 kg
PB
PB700S
/ 52 ⅔" x 43 ⅘" x 26 ⅔"
/ 131.2 lb
6
1
2
4
6
7
10
8
14-2
14-4
9
14-1
14-3
13
14
15
A
16
B
C
COOKING AREA TEMP. RANGE DIGITAL FEATURES
Eight temperature
Main - 3,271 cm² / 507 sq. in.
82-260°C
presets, start-up and
Upper Rack - 1,245 cm² / 193 sq. in.
/ 180-500°F cool-down cycles,
TOTAL - 4,516 cm² / 700 sq. in.
electric igniter
Parts are located throughout the shipping carton, including underneath the grill. Inspect the grill, parts, and hardware blister
pack after removing from the protective shipping carton. Discard all packaging materials from inside and outside of the grill
before assembly, then review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not attempt
to assemble. Shipping damage is not covered under warranty. Contact your dealer or Pit Boss Customer Service for parts: Monday
through Sunday, 4am - 8pm PST (EN/FR/ES).
3
service@pitboss-grills.com | Toll-Free: 1-877-303-3134 | Toll-Free Fax: 1-877-303-3135
IMPORTANT: To ease installation, using two people is helpful (but not necessary) when assembling this unit.
5
Tools required for assembly: screwdriver and level. Tools not included.
IMPORTANT: It is advised to read each step entirely before starting assembly on instructions. Do not tighten screws
completely until all screws for that step have been installed. Hardware combination involving a locking washer and
11
washer should be installed with the locking washer closest to the head of the screw.

1. MOUNTING THE WHEELS TO THE LEGS

Parts Required:
12
4 x Support Leg (#14)
4 x Locking Caster Wheel (#15)
Installation:
• Insert one of the pre-threaded locking caster wheels into the bottom
of a support leg by hand-tightening it into the hole. Continue to install
the other caster wheels to the remaining support legs.

2. ASSEMBLING THE CART

Parts Required:
1 x Bottom Shelf (#16)
8 x Screw (#A)
Locking Washer (#C)
8 x
8 x Washer (#B)
Installation:
• Attach the bottom shelf to one of the four support legs using two washers,
locking washers, and screws. Note illustration for support leg placement.
• On a level surface, continue to secure the other support legs to the
bottom shelf. The edge of the bottom shelf with holes should face
forward. The bottom shelf holes will remain un-used.
NOTE: Ensure the support leg with two screws is facing the front.

ASSEMBLY PREPARATION

ASSEMBLY INSTRUCTIONS
1
2
14-1
A
14-2
14-4
14-3
C B
7