Hints And Warning; Warning; Shipping And Transporting The Pump; Proper Use Of The Pump - ETATRON D.S. BH3-V Notice D'installation, Emploi Et Entretien

1.0 - HINTS AND WARNINGS
Please read the warning notices given i n this section very carefully, becaus e they provide important in formation regarding
safety in installation, use and maintenance of the pump.
• Keep this manual in a safe place, so that it will always be available for further consultation.
• The pump complies with EEC direct ives No.89/336 regarding "electromagnetic comp atibility" and No .73/23 regarding
"low voltages", as also the subsequent modification No.93/68.
N.B. The pump has been constructed in a ccordance with best practice. Both its life and it electrical and
mechanical reliability will be enhanced if it is correctly used and subjected to regular maintenance.

1.1 - WARNING:

Any intervention or repair to the internal parts of the pump must be c arried out by qualified and authorized
personnel. The manufacturers decline all responsibility for the consequences of failure to respect this rule.
GUARANTEE: 2 years (the normal wearing parts are excluded, i.e.: valves, nipples, tube nuts, tubing, filter and
injection valve). Improper use of the equipment invalidates the above guarantee. The guarantee is exfactory or
authorized distributors.

1.2 - SHIPPING AND TRANSPORTING THE PUMP

No matter what the means of transport employed, delivery of the pump, even when free to the purchaser's or the addressee's
domicile, is always at t he purchaser's risk. Clai ms for any missing materials must be made within 10 (ten) days of a rrival,
while claims for defective materials will be considered up to the 30th (thirtieth) day following receipt. Return of pumps or
other materials to us or the authorized distributor must be agreed beforehand with the responsible personnel.

1.3 - PROPER USE OF THE PUMP

• The pump should be used only for the purpose for which it h as been expressly designed, namely the dosing
of liquid additives. Any different use is to be considered improper and therefore dangerous.Th e pump should not
therefore be used for applications that were not allowed for in its design. In cas e of doubt, please contact our
offices for further inf
The manufactures cannot be held res
use of the pump.

1.4 - RISKS

• After unpacking the pu mp, make sure it is completely sound. In case of doubt, do no t use the pump and con-
tact qualified personnel. The packing materials (especially bags mad e of plastics, polystyrene, etc.) s hould
be kept out of the reach of children: they constitute potential sources of danger.
• B efore you connect the pump, make s ure that the voltage ratings, etc., correspond to your particular power
supply. You will find these values on the rating plate attached to the pump.
• The electrical installation to which the pump is connected must comply with t he standards and good prac-
tice rule in force in the country under consideration.
• Us e of electrical equipment always implies observance of s ome basic rules: In particular: 1 - do not touch the equipment
with wet or damp hands or feet;
2 - do not operate the pump with bare feet (Example: swimming pool equipment);
3 - do not leave the equipment exposed to the action of the atmospheric agents;
4 - do not allow the pump to be used by children or unskilled individuals without supervision;
• In case of breakdown or imp roper functioning of the pump, switch off, bu t do not touch. Contact our techni-
cal assistance for any necessary repairs and insist on the use of or iginal spares. Failure to respect this con-
dition could render the pump unsafe for use.
• When you decide to make no further use of an installed pump, make sure to disconnect it f rom the power
supply.
Before carrying out any service on the item, check:
1. Disconnect from the ma ins or b y means of a single pole circuit breaker, having 3 mm minimum distance
between the contacts. (Fig. 4).
2. Relieve all the pressure from the injection tube.
In event of possible losses in the hydraulic system of the pump (breakage of the "O" ring gasket, the valves or the hoses)
the pump should immediately be brought to a stop, emptying and depressurizing the delivery hose while taking all due
safety precautions (gloves, goggles, overalls, etc.).
ormation about the c
ponsible for damage deriving f rom improper, erroneous or unreasonable
haracteristics of the p
• 10 •
ump and its proper use.