Technical Data; Cs 2152 - Jonsered CS 2152 Manuel D'utilisation

Engine
3
Cylinder volume, cu.in/cm
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication system
Manufacturer
Carburetor type
Fuel capacity, US pint/litre
Oil pump capacity at 8500 rpm, ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain, Lbs/kg
Chain/bar
Standard bar length, inches/cm
Recommended bar lengths, inches/cm
Usable cutting length, inches/cm
Chain speed at max. power, m/sec
Pitch, inch/mm
Thickness of drive link, inch/mm
Number of teeth on drive sprocket
34
– English

TECHNICAL DATA

CS 2152

3,2/51,7
1,77/45,0
1,28/32,5
2 700
2,4/ 9 000
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
Zama
C3-EL18
1,06/0,50
5-10
0,59/0,28
Automatic
CS 2152: 11,0/5,0
CS 2152 W: 11,2/5,1
CS 2152 WH: 11,2/5,1
CS 2152 C: 11,0/5,0
CS 2152 CW: 11,2/5,1
CS 2152 CWH: 11,2/5,1
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
0,063"/1,6
7
RECOMMENDED CUTTING EQUIPMENT
FOR CANADA
The following is a list of recommended cutting equipment
for Class 1A and 1B Chainsaws.
The combinations of powerhead, bar and chain meet all
requirements outlined in the CSA Z62.1-95 Chainsaws and
Z62.3-96 Chainsaw Kickback standards.
The guide bar nose radius is determined by either the
maximum number of teeth in the nose sprocket or the
corresponding maximum nose radius of a solid bar.
As we are listing the maximum guide bar nose radius, you
may use a guide bar with smaller nose radius than in our
list. For guide bars of the same length, all sprocket-nose
guide bars of the same pitch and having the same number
of sprocket teeth may be considered to have equivalent
kickback energy.
A hard nose bar having the same length and nose radius
as a sprocket-nose bar may be considered to have
equivalent or less kickback energy than the sprocket-nose
bar.
We recommend that you as replacement use the listed bars
and chains or "Type C Low-Kickback Saw Chains" which
are available at your dealer.
Guide bar Saw chain
Length Pitch Max nose
inch inch radius
13 0,325" 10T Jonsered S30 or Oregon 95VP
15 0,325" 10T
16 0,325" 10T
18 0,325" 10T
20 0,325" 10T
13 0,325" 10T Jonsered S25 or Oregon 21BP
15 0,325" 10T
16 0,325" 10T
18 0,325" 10T
20 0,325" 12T
15 0,325" 10T Total/Sabre 528PS
16 0,325" 10T
18 0,325" 10T
20 0,325" 12T
15 0,325" 10T Total 528NK, Total 528NKD
16 0,325" 10T Sabre 528P (Single or Dual Raker)
18 0,325" 10T or Sabre 528P (Single or Dual Raker)
Note: For the chains above you are free to choose between
0,050", 0,058" and 0,063" gauge drive link for the corresponding
bar, see table below.
0,050" (1,3 mm) S30 / 95VP
0,058" (1,5 mm) – S25 / 21BP
0,063" (1,6 mm) –
20BP 520PS –
528PS 528NK/NKD
22BP 523PS –
–
528P
–