Maintenance And Service Instructions; Cleaning; Repair Service; Warranty - stayer RO5 BRUSHLESS Instructions D'emploi

Sanding Surfaces
Switch the machine on, place it with the complete sanding
surface on the surface to be worked and move the machine
with moderate pressure over the workpiece.
The removal capacity and the sanding pattern are mainly
determined by the selection of the sanding sheet, the
preselected orbital stroke rate and the applied pressure.
Only flawless sanding sheets achieve good sanding
capacity and extend the service life of the machine.
Pay attention to apply uniform sanding pressure; this
increases the working life of the sanding sheets.
Intensifiying the sanding pressure does not lead to an in-
crease of the sanding capacity, but to increased wear of
the machine and the sanding sheet.
A sanding sheet that has been used for metal should not
be used for other materials.
Use only original STAYER sanding accessories.
Rough Sanding
Attach a sanding sheet with coarse grain.
Apply only light pressure to the machine so that it runs at a
higher stroke rate and high material removal is achieved.
Fine Sanding
Attach a sanding sheet with fine grain.
By lightly varying the application pressure or changing the
orbital stroke rate, the sanding plate stroke rate can be
reduced whereby the orbital action is maintained.
With moderate pressure, move the machine in a circular
pattern or alternately in lengthwise and crosswise directions
over the workpiece. Do not tilt the machine to avoid sanding
through the workpiece (e. g. when sanding veneer).
After finishing the working procedure, switch the power
tool off.
Polishing
Note: For polishing, the extraction outlet piece can be
removed for easier handling of the machine and to prevent
damage to the workpiece.
For the polishing of weathered paint or buffing out scratches
(e. g., acrylic glass), the machine can be equipped with
appro- priate polishing accessories such as lamb's wool
bonnet, polishing felt or sponge (accessories).
Select a low stroke rate for polishing in order to avoid
excessive heating of the surface.
Apply the polish onto a somewhat smaller surface than
you intend to polish. Work the polishing agent in with a
suitable polishing tool applying it crosswise or with circular
motion and moderate pressure.
Do not allow the polishing agent to dry out on the surface,
otherwise the surface can become damaged. Do not
subject the surface to be polished to direct sunlight.
Clean the polishing accessories regularly to ensure good
polishing results. Wash out polishing accessories with a
mild detergent and warm water; do not use paint thinner.
ENGLISH
15

5. Maintenance and service instructions

5.1 Cleaning

Before any work on the machine itself, pull the
mains plug.
For safe and proper working, always keep the
machine and ventilation slots clean.
If the replacement of the supply cord is necessary,
this has to be done by STAYER or an authorized STAYER
service agent in order to avoid a safety hazard.
If the machine should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an aftersales service centre for STAYER
power tools.

5.2 Repair service

Our after-sales service responds to your questions
conceming maintenance and repair ofyour product as well
as spare parts.
Exploded views and information on spare parts can also
be found under: info@grupostayer.com
Our customer consultants answer your
conceming best buy, application
productsand accessories.

5.3 Warranty

Warranty card
lncluded in the documentation that accompanies this
equipment, you should find the warranty card. You should
fill out the card completely and retum to vendar with a copy
of purchasing receipt or invoice and you should receive a
receipt.
Note: lf you cannot find the warranty card within the
documentation,youmust ask for it through your supplier.
The warranty is limited only to manufacturing defects and
expire if pieces have been removed or manipulated or
repaired otherthan themanufacturer.

5.4 Disposal and recycling

The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
OnlyforEC countries:
Do not dispose of power tools into
household waste!
According the European Guideline 2002/96/
EC for Waste Electrical and Electronic
Equipment
national right,power tools that are no longer
usable must be collected separately and disposed of in an
environmentally correct manner.
Subject to change wlthout notice.
15
questions
and adjustment of
and its implementation into