Electrical Connection; Ilustrated Description; Operating Instructions; Placement And Testing - stayer HP750BE Instructions D'emploi

Mount straight access cover
- Pull out and the lid port 12 straight head sander.
Disassembly access cover straight
- Place the lid on the right access notches 12 in the san-
ding head.

3.3 Electrical connection

The network voltage must conform to the voltage indi-
cated on the tool name plate. Under no circumstances
should the tool be used when the power supply cable is
damaged.
A damaged cable must be replaced immediately by an
authorized Customer Service Centre. Do not try to repair
the damaged cable yourself. The use of damaged power
cables can lead to an electric shock.

3.4 Ilustrated description

1. Sanding paper.
2. Sanding plate.
3. Dust bag.
4. Speed adjusting wheel.
5. Lock switch.
6. Soft grip.
7. Auxiliary handle.
8. Power supply cable.
9. Vacuum hose.
10. Suction nozzle .
11. ON/OFF switch.
12. Bindings straight access.

4. Operating instructions

4.1 Placement and testing

Once the machine and vacuum cleaner are tight and that
all safety measures and equipment are in place, start by
turning on the vacuum cleaner and then the machine. (If
you are using a vacuum cleaner with integrated switch,
simply turn on the machine).
- Begin sanding and carefully contact the work surface
as lightly as possible-just enough to keep the sanding
head flat against the surface.
- The joist in the sanding head allow the sanding disc to
follow the contours of the work surface.
- The best technique is to use overlapping sweeps and
keep the head in constant motion. Never stop too long
in any one place or there will be swirl marks. With ex-
perience it will be very easy to create excellent results.
Ensure that the sandpaper you are using is
suited to the task, Overly coarse grit paper may
remove material too quickly to control. While
overly fine grit paper may clog too often and not
shape down the surface.
Take care to avoid sharp projections and nails,
etc. This will wipe out the sandpaper and
probably damage the dish as well.
Unions sanding walls or ceiling, wall and remove the co-
vers 12 to reach every inch sanding.
ENGLISH
12

4.2 Tool change

Changing sanding pad (fig.3)
- Insert the hex key (supplied) into the screw with hex
sanding pad 2.
- Insert the tool in "V" (supplied with the kit) on 2 suction
holes to lock the plate holding the tool by hand.
- Turn the hex wrench to remove the plate.
- Install the new sanding tightening the bolt.
Install a sanding machine specified.
Glue sandpaper to the plate
Make sure the holes in the sandpaper one perfectly co-
rrespond to the suction holes of the plate 2.
Dust extraction
The exhaust system 4 hole collects fine dust particles,
which enables the tool to adhere to the wall and ceiling
with a perfect dust extraction effect.
Connect to dust bag
The dust bag 3 must be connected to the hose, adjusting
the Velcro 8 to end of the suction hose 9.
Clean the dust bag at the right time.

4.3 Tuning operations

Adjusting the rotation speed
The speed of the machine is variable to suit different
tasks. It can be adjusted from 1200 min
by using the thumb wheel 4. Turn to increase or decrease
the speed. Generally, you should use the higher speed for
fast stock removal and the lower speed for more precise
control.

5. Maintenance and service instructions

5.1 Cleaning

Keep tool clean
Periodically blow out all air passages with dry compressed
air. All plastic parts should be cleaned with a soft damp
cloth. NEVER use solvents to clean plastic pats. They
could possibly dissolve or otherwise damage the material.
Wear safety glasses while using compressed air.
Clean the vacuum swivel connector as too much dust will
keep it from turning freely.

5.2 Repair service

Our after-sales service responds to your questions
conceming maintenance and repair ofyour product as well
as spare parts.
Exploded views and information on spare parts can also
be found under: info@grupostayer.com
Our customer consultants answer your questions
conceming best buy, application and adjustment of
productsand accessories.

5.3 Warranty

Warranty card
lncluded in the documentation that accompanies this
12
up to 2200 min
-1 -1