Grinding And Sanding; Maintenance Instructions; Cleaning, Maintaining, Lubricating, Sharpening; Repair Service - stayer AGL115 Instructions D'emploi

6. Disk guard
7. Battery clip
8. Battery
9. Spindle
10. Grinding disk
11. Internal flange
12. External flange
13. Soft grip
14. Service wrench
15. Air outlet opening
16. Air inlet opening
17. Lateral grip
18. Red indicator light (battery charging)
19. Battery charge indicator button
20. Charge indicator
21. Adjustment screw of the disk guard
4. Operating instructions
Make sure that you understand and comply with all safety
instructions.
WARNING! Always use safety goggles and gloves while
using the machine.
• Do not force the machine by pressing it excessively.
The weight of the tool already applies the adequate
pressure. If you force it and apply excessive pressure,
the disk might get damaged with the hazard involved.
• ALWAYS replace the disk if the tool falls down during
grinding.
• NEVER knock the grinding disk or any other disks
against the work piece.
• Avoid the disk bouncing or getting stuck, especially
when working at corners, sharp edges, etc. This might
cause a loss of control and abrupt kickbacks.
• NEVER use this tool with disks fur cutting wood or any
other sawing disks. With these saws, the tool may
kickback strongly and cause injuries.
CAUTION! The depth of one single cut may reach up to 5
mm. Adjust the pressure to the tool so that the speed of the
tool is not reduced during its use.
• After having finished the job, always switch of the tool
and wait until the disk has stopped completely before
leaving the tool.
• If the tool is used continuously until the battery
cartridge has become discharged completely, let the
tool rest for 15 minute before continuing with a charged
battery.

4.1. Grinding and sanding

ALWAYS hold the tool firmly with one hand at the body of
the tool and the other hand at the lateral grip 17. Switch it on
and apply the disk 10 to the work piece.
Normally, advance maintaining the edge of the disk 10 in an
angle of about 15 degrees with respect to the surface of the
work piece.
WARNING! If you force or exert excessive pressure, or you
allow the disk to become bent, get stuck or become forced
when cutting, this may cause the motor to overheat and a
dangerous kickback of the tool.
CAUTION! Once the cutting operation has been carried
out, make sure that the disk has stopped completely.
ENGLISH
(Fig. 2)
15
Thereafter, you can leave the tool on a surface. It is
dangerous to leave the tool on a surface before having
switched it off. If there is dust or dirt around the tool, these
may be absorbed by the tool.
Make sure that the disk does not enter into contact with the
work piece. Switch the tool on and hold it firmly. Wait until
the tool has reached its maximum speed, Now you only
have to push the tool forward on the surface of the work
piece, maintaining it flat and advancing smoothly until the
cutting process has been completed.

5. Maintenance instructions

5.1. Cleaning, maintaining, lubricating,
sharpening.
Extract the battery before any manipulation of the tool.
Maintain the tool and the grid clean in order to work
efficiently and safely.
• Excessive dirtiness of the tool may cause it to work
deficiently.
• Should the electric tool, despite the thorough
manufacturing and control processes, get damaged,
the repair must be entrusted to a technical service
authorized for Stayer tools.
• For any question or request for spare parts it is
indispensable to state the model of the machine that
appears on the plate of characteristics on the tool.

5.2. Repair service

The technical service will provide you advice regarding
questions you may have on the repair and maintenance of
your product as well as on spare parts. You may also obtain
exploded views and information on spare parts on the
internet under:
info@grupostayer.com
Our team of technical advisors will be glad to guide you
regarding acquisition, application and adjustment of
products and accessories.
DISPOSAL
It is compulsory to subject electric tools, accessories and
packaging to a recovery process that respect the
environment.
For EU countries only:
Do not throw away electric tools!
In accordance with European Directive
2002/96/EC on unserviceable electric and
electronic apparatus, after its transposition into
national law, they must be collected separately
to subject them to ecologic recycling.
The right to amendment is reserved.
15