Publicité
Les langues disponibles
Les langues disponibles
Connecting the drive motors
When installing the motor cables, please ensure there is no
danger that they may become torn or damaged.
Cut motor cable of drive motor that is furthest away from
control unit to length. Shorten the motor cable of the nearest
drive motor to the same length. The two drive motor cables
must be of the same length to ensure that the drive output of
the Mover® is uniform! Excess cable must be routed in wavy
lines without looping.
Crimp the provided flat plugs onto the drive motor cables.
Release flap at control unit terminal strip by pressing and
connect cables as shown in wiring diagram (red = positive,
black = negative). Please ensure that the connections are
made properly!
Connecting the battery
Liquid electrolyte batteries need to be placed in a separate
box with an external venting system. The fuse for the positive
line needs to be connected outside the box. The gel and AGM
batteries do not need a separate box. Observe the installation
regulations of the battery manufacturer.
The cables leaving the terminal need to be installed separately
from each other until after the fuse in the plus line.
-
+
Fig. 29
Route battery connecting cables (only use the original Truma
cables included in the delivery) to control unit and securely
attach using the provided clips and screws.
The battery connecting cables must not be extended.
They must be routed separately from the motor cables,
and must not run over the control unit.
Route battery connecting cables so that they do not chafe
(particularly at leadthroughs through metal panels). Use suit-
able leadthrough grommets for protection in order to prevent
damage to cables. Connect battery connecting cables to the
existing battery terminals (red = positive, black =
negative).
Incorrect wiring will destroy the electronics / control
system.
The connection to the control unit (as per the connecting dia-
gram) must take place in the order – nut, battery connection
ring, nut (torque 7 Nm ±1).
Connect the fuse in the positive cable (150 A) close to the
positive contact.
22
-
+
Commissioning the Mover®
Ensure the battery used to operate the Mover® is fully charged.
Park the caravan outside on an open, level surface and apply
the handbrake. Ensure that the rollers are disengaged from
the road tyres and the corner steadies are raised.
Connect battery terminals to battery, check that all cables are
secure and not hot or indicating signs of short circuits, etc.
Move slide switch on remote hand set to the "On"
This switches the remote hand set on – green LED flashes for
5 seconds in combination with the acoustic alarm until the
control unit is ready for operation. If LED does not illuminate,
check polarity and condition of batteries in remote hand set.
The remote hand set switches itself off after about 2 minutes
if no buttons are pressed.
Check whether both drive motors are stationary. With the re-
mote hand set switched on, and no more than 2 m away from
the control unit, press the "Forwards" button. Both drive mo-
tors must now move in the forwards direction.
Move slide switch on remote control to the "Off"
to switch the remote control and therefore the Mover® off.
Move drive rollers against the tyres using the provided lever.
Turn the lever until it mechanically engages and cannot be
turned any further without using excessive force (end position
approximately horizontal).
Ensure that there no obstacles around the caravan, release
the handbrake and switch the remote control on. Now
check all functions several times according the operating
instructions.
Apply caravan handbrake. To switch the remote hand set and
the Mover® off, move slide switch on remote hand set to the
"Off"
position. Release drive rollers using the lever and re-
check distance between roller and tyre. Adjust if necessary.
The distance between the disengaged drive rollers and
the tyres is 20 mm.
Warning information
The yellow sticker with the warning information, which is
enclosed with the appliance, must be affixed by the installer
or vehicle owner to a place in the vehicle where it is clearly
visible to all users (e.g. on the wardrobe door)! Ask Truma to
send you a sticker, if necessary.
❙
position.
position
Publicité
Chapitres
