Installation Instructions; Manufacturer's Terms Of Warranty; Intended Use; Approval - Truma Mover SR Instructions De Montage Et Mode D'emploi

Manufacturer's terms of warranty

1. Case of warranty
The manufacturer grants a warranty for malfunctions in the
appliance which are based on material or production faults.
In addition to this, the statutory warranty claims against the
seller remain valid.
A claim under warranty shall not pertain:
– for parts subject to wear and in cases of natural wear
and tear,
– as a result of using components in the units that are not
original Truma parts,
– for gas pressure regulation systems as a result of damage
by foreign substances (e.g. oils, plasticisers) in the gas,
– as a consequence of failure to respect Truma instructions
for installation and use,
– as a consequence of improper handling,
– as a consequence of improper transport packing.
2. Scope of warranty
The warranty is valid for malfunctions as stated under item 1,
which occur within 24 months after conclusion of the pur-
chase agreement between the seller and the final consumer.
The manufacturers will make good such defects by subse-
quent fulfilment, i.e. at their discretion either by repair or
replacement. In the event of manufacturers providing service
under warranty, the term of the warranty shall not recom-
mence anew with regard to the repaired or replaced parts;
rather, the old warranty period shall continue to run. More
extensive claims, in particular claims for compensatory dam-
ages by purchasers or third parties, shall be excluded. This
does not affect the rules of the product liability law.
The manufacturer shall bear the cost of employing the Truma
customer service for the removal of a malfunction under war-
ranty – in particular transportation costs, travelling expenses,
job and material costs, as long as the service is carried out in
Germany. The warranty does not cover customer service work
in other countries.
Additional costs based on complicated removal and installa-
tion conditions of the appliance (e.g. removal of furniture or
parts of the vehicle body) do not come under warranty.
3. Raising the case of warranty
The manufacturer's address is:
Truma Gerätetechnik GmbH & Co. KG
Wernher-von-Braun-Straße 12
85640 Putzbrunn, Germany
Always notify the Truma Service Centre or one of our author-
ised service partners if problems are encountered (see Truma
Service book or www.truma.com). Please describe you com-
plaint in detail and state the factory number of the device and
the purchase date.
In order for the manufacturer to be able to determine whether
an incident subject to guarantee has occurred, the end user
must, at his own risk, bring or send the device to the manu-
facturer. If there is damage to heat exchangers, the gas pres-
sure regulator must also be sent back to the factory.
Air conditioners:
To avoid transportation damage, the unit may only be sent to
the Truma Service Centre Germany or one of our authorised
service partners if agreed beforehand. Otherwise the sender
bears the risk for any transportation damage.
Please send all shipment to the factory as freight. In cases
under guarantee, the works shall bear the transport costs or
the costs of delivery and return. If the damage is deemed not
to be a warranty case, the manufacturer shall notify the cus-
tomer and shall specify repair costs which shall not be borne
by the manufacturer; in this case, the customer shall also bear
the shipping costs.

Installation instructions

Before commencing any work, read and observe the installa-
tion instructions carefully!
Please ensure that no metal chips or other contaminants get
into the controller during installation.
In the case of screws with sealants, steps must be
taken to ensure that the thread is free of grease / oil.

Intended use

The Mover® SR has been built for use with single-axis caravans
with a gross weight of up to 2000 kg.
The Mover® SR weighs approx. 34 kg with the cross
actuation device attached.
Check the towing load of your vehicle and the gross weight of
your caravan in order to establish whether they are designed
for the additional weight.

Approval

The Truma Mover® SR has design approval, and a general
operating permit (ABE) has been issued for Germany. Accept-
ance by a vehicle expert is not required (except when install-
ing the low chassis kit). The ABE must be kept in the vehicle.
The Mover® satisfies other requirements stated in the EG di-
rectives and standards (see declaration of conformity).
The technical and administrative regulations of the country in
which the vehicle is initially registered must be complied with
when the Mover® is being installed.
Any modifications to the unit, or the use of spare parts and
accessories that are important to the operation of the system
that are not original Truma parts and failure to follow the in-
stallation and operating instructions will cancel the warranty
and indemnify Truma from any liability claims. In addition to
this, the operational approval for the device will be cancelled.

Tools and facilities required

To install the unit you will need:
– 13 mm, 17 mm, 10 mm socket wrench, ring spanner or
open-jawed spanner
– Torque wrench (5 – 40 Nm)
– Cable cutter / Crimping tool
– Power drill / screwdrivers / 25 mm hole cutter
– Portable 2 tonne trolley jack and axle stands to suit
– Appropriate lighting
17