Analog way OCTO-FX2 Manuel Utilisateur page 35

²
OCTO / QFX402
8-5 [LAN setup] + ENTER. (Available with the LAN option only)
Allows configuring the LAN communication port. Select the UDP or TCP protocol with
select items with
• [Device addr.]:
• [Remote addr.]: This is the destination IP address used with an outgoing connection. Select the destination IP
• [Gateway addr.]: The gateway address, or router, allows communication to other LAN segments. The gateway
• [Device port]:
• [Remote port]:
• [Netmask]:
• [Default setup]:
MAC ADDRESS: The MAC address, also referred to hardware address, is a unique number assigned to each
8-6 [Key locking] + ENTER.
Select an item with
• [All]:
• [Menus]: Locks/unlocks the LCD CONTROL switches.
• [Input]: Locks/unlocks the INPUT SELECTION and FREEZE switches.
NOTE: To unlock presses simultaneously on ENTER and EXIT.
• [Autolock]: Allows selecting an input only if a signal is connected.
8-7 [Stand-by] + ENTER.
8-7-1 [Baud rate] + ENTER.
Select the baud rate of the display device with
8-7-2 [Message ON] + ENTER.
This function allows to store the ON message of your display device. Then your device coming out the
STANDBY mode, this one send the stored message to your display device. The ON message can be
composed up to 50 bytes. For each byte, select the needed ASCII code with
ENTER.
NOTE: The 0 value allows to displays: no data.
8-7-3 [Message OFF] + ENTER.
This function allows to store the OFF message of your display device. Then your device going into the
STANDBY mode, this one send the stored message to your display device. The OFF message can be
composed up to 50 bytes. For each byte, select the needed ASCII code with
NOTE: The 0 value allows to displays: no data.
8-7-4 [Reset mess ON] + ENTER.
Allows to reset the ON message.
8-7-5 [Reset mess OFF] + ENTER.
Allows to reset the OFF message.
+ ENTER.
Every device connected to an IP network must have a unique IP address. This address is used
to reference the specific unit. IP addresses are specified as x.x.x.x where each x is a number
from 1 to 254. Assign the device to a unique IP address with
192.168.0.2).
address with
address should be the IP address of the router connected to the same LAN segment as the
unit. Select the gateway address with
Every TCP connection and every UDP datagram is defined by a destination IP address and a
port number. Select a local port number with
(Default value: 10500).
You must set the remote TCP port number for the unit to make outgoing connections. This
parameter defines the port number on the target host to which a connection is attempted.
Select a remote port number with
value: 10500).
A netmask defines the number of bits taken from the IP address that are assigned for the host
section. The device prompts for the number of host bits to be entered, then calculates the
netmask, which displays in standard decimal-dot notation when the saved parameters are
displayed. Select the netmask with
Set all the LAN settings to the default value. Select [YES] and validate with ENTER.
device. The MAC address is available on the bottom device label.
and change the mode with ENTER.
Locks/unlocks all the front panel switches.
Chapter 5 : FRONT PANEL DISPLAY MENUS DESCRIPTION (continued)
+ ENTER. (Default value: 192.168.0.1).
+ ENTER. (Default value: 192.168.0.1).
+ ENTER between 00000 and 655000. (Default
+ ENTER. (Default value: 255.255.255.0).
+ ENTER between 9600, 2400 & 1200.
+ ENTER then
+ ENTER. (Default value:
+ ENTER between 10000 and 10999.
and validate with
, then press ENTER.
PAGE 35