Analog way Di-Ventix DVX8022 Manuel Utilisateur page 61

Di-VentiX™
6-5. FRONT PANEL SCREEN FUNCTIONS DESCRIPTION (continued)
9 [CONTROL]
9-1 [versions] + ENTER.
Display the status of the internal firmware.
• A = xxxx
• D = xxxx
9-2 [auto TAKE]
This function allows switching directly from the input select button (without pressing the TAKE button).
9-3 [RS232/LAN port] + ENTER.
Select the needed communication port with
• [RS232]: Enables the RS-232 communication port. (Default setting).
• [LAN]: Enables the LAN communication port.
IMPORTANT: To avoid addresses conflict, configure the LAN communication port (with the LAN setup
NOTE: The RS-232 & the LAN communication ports can not be used simultaneously.
9-4 [LAN setup] + ENTER.
Allows configuring the LAN communication port. Select items with
• [local addr.]:
• [remote addr.]: This is the destination IP address used with an outgoing connection. Select the destination IP
• [gateway addr]: The gateway address, or router, allows communication to other LAN segments. The gateway
• [local port]:
• [remote port]: You must set the remote TCP port number for the unit to make outgoing connections. This
• [netmask]:
• [default setup]: Set all the LAN settings to the default value. Select [YES] and validate with ENTER.
MAC ADDRESS: The MAC address, also referred to hardware address, is a unique number assigned to each
9-5 [transition] + ENTER. This menu is available in MATRIX mode only.
Select a type of transition between:
9-5-1 [fade color] + ENTER.
This function allows selecting the color of the fade during the transition. Select a color (red, green and
bleu) with
displayed onto the output. To obtain the black color, set the 3 levels to the minimum. To obtain the white
color, set the 3 levels to maximum. To obtain the grey color, set the 3 levels in the middle.
9-5-2 [fade frame] + ENTER.
This function allows switching by a fading image (instead of a color). Then adjust the duration of the
transition.
9-5-3 [clean cut] + ENTER.
This function allows a clean switching thanks to a fast freeze of the displayed source.
• B = xxxx • X = xxxx
• K = xxxx • V = xxxx (optional)
menu) before activates it.
Every device connected to an IP network must have a unique IP address. This address is used
to reference the specific unit. IP addresses are specified as x.x.x.x where each x is a number
from 1 to 254. Assign the device to a unique IP address with
192.168.0.2).
address with + ENTER. (Default value: 192.168.0.1).
address should be the IP address of the router connected to the same LAN segment as the unit.
Select the gateway address with
Every TCP connection and every UDP datagram is defined by a destination IP address and a
port number. Select a local port number with
(Default value: 10500).
parameter defines the port number on the target host to which a connection is attempted. Select
a remote port number with
10500).
A netmask defines the number of bits taken from the IP address that are assigned for the host
section. The device prompts for the number of host bits to be entered, then calculates the
netmask, which displays in standard decimal-dot notation when the saved parameters are
displayed. Select the netmask with
device. The MAC address is available on the rear panel device label.
+ ENTER and adjust the level with
Chapter 6 : Di-VentiX & REMOTE KEYPAD SCREEN DESCRIPTION (continued)
• Y = xxxx
• I = Identification number.
+ ENTER.
+ ENTER. (Default value: 192.168.0.1).
+ ENTER between 00000 and 655000. (Default value:
+ ENTER. (Default value: 255.255.255.0).
+ ENTER. During the adjustment the color is
• S = xxxx
+ ENTER.
+ ENTER. (Default value:
+ ENTER between 10000 and 10999.
PAGE 61