Cardin SLX Série Mode D'emploi page 15

SCREW OPERATED MANUAL RELEASE SYSTEM
SLX1524 - SLX824
To release the unit
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
1. Lower the lock protection 'A' on the release knob, insert the
key 'B' and rotate it through 180 degrees clockwise. The knob
is now free and can be rotated.
2. Rotate the knob 'C' clockwise until reaches its travel limit.
The geared motor is now released and the gate can be moved
manually.
Attention! Do not force the knob to exceed the travel limit.
To relock the unit
1. Rotate the knob 'D' anticlockwise until it blocks completely.
2. Rotate the key anticlockwise and position the lock protection.
The geared motor is now locked and the gate may be used
normally.
Once the system has been reset store the key in a safe place.
Attention! Never use the manual release mechanism
while the gate is in operation.
Moving the gate manually will force the encoder to
lose the position of the gate. To reset the control, once
the gate has been relocked, you will need to give 3
or more movement commands so that the gate leaf
will reach the travel limit enough times to position
itself correctly.
Access to the electronic card
Attention! Before opening the cover make sure that the power
has been switched off at the mains. To access the motor loosen
the two screws 'A' positioned on either end of the cover as
indicated in figure 11.
ELECTRICAL CONNECTION
Important remarks
• After having installed the device, and before powering
up the programmer, release the door (manual release
mechanism) and move it manually, checking that it moves
smoothly and has no unusual points of resistance.
• The presence of the electrical current sensor does not
dispense with the obligation to install photoelectric
cells and other safety devices foreseen by the safety
standards in force.
• Before connecting the appliance make sure that the
voltage and frequency rated on the data plate conform
to those of the mains supply.
• The motor's power cable must be made of polychloroprene
in conformity with the international standard 60245 IEC
57 (e.g. 3 x 1.5 mm
Drawing number :
• The cable may only be replaced by qualified technicians.
Product Code :
• An all pole trip switch with at least 3 mm between the
Draft :
contacts must be installed between the unit and the
mains supply.
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
• Don't use cables with aluminium conductors; don't
solder the ends of cables which are to be inserted into
the binding posts; use cables marked T min 85°C and
resistant to atmospheric agents.
• The terminal wires must be positioned in such a way
that both the wire and the insulating sheath are tightly
fastened.
Drawing number : DM0801
Product Code : SL1524SB
Draft : P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Drawing number :
DM0803
Product Code : SL1524SB
Draft : P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
H05RN-F).
2
DI0286
Date : 06-03-95
P.J.Heath
A
5 - 6 turns
C
MAINS POWER SUPPLY CONNECTION 230 Vac
• Connect the control and security device wires.
Description : Sblocco nuovo "A"
• Run the mains power supply through the cable clamp located on
SL1524SB
the bottom right of the main circuit board and to the separate
Date : 13-11-2008 3-way terminal board:
Drawing number :
N
Product Code :
Draft : P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/4018
L
Drawing number :
Description : Sblocco nuovo "C"
Electronic programming unit
Product Code : SL1524SB
SL1524SB
Instructions for programming the ECU and battery powered
Draft : P.J.Heath
Date :
13-11-2008
operation can be found in the MULTI-ECU SOFTWARE manual
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fa
ZVL608 supplied with the automation.
MAINTENANCE
To use the 24 month or 50000 manoeuvre guarantee, read the
following notes carefully.
Attention! Before carrying out any cleaning or maintenance
operations make sure the power is disconnected at the mains,
the motor power cables are disconnected and the batteries
have been disconnected.
Eventual repair work must be carried out by specialised per-
sonnel using original spare parts.
The motor does not normally require particular maintenance; in
any case the 24 month or 50000 manoeuvre guarantee is only
valid if the following controls have been observed and eventual
maintenance has been carried out to the machine 'sliding gate':
Fissaggio placca inferiore
Description :
- check the straightness of the toothed rack, make sure the teeth
Collegamento motore
fit correctly in the pinion throughout its entire length; in particular
the gear rack must have a cross section of 20 x 20 mm;
- check the play of the gear rack - pinion (1-2 mm see fig. 7/10);
- periodically check the moving parts for wear and tear and
grease if required, using lubricants which maintain their friction
levels unaltered throughout time and are suitable for temper-
atures of -20 to +70°C;
- check the battery charge level.
These checks must be written down as they are paramount in
validating the guarantee.
15
SLX1524 - SLX824
5 - 6 turns
D
Description :
DM0802
- connect the neutral to binding post N
SL1524SB
SL1524SB
- connect the earth to binding post
Date : 13-11-2008
- connect the live to binding post
Description :
DM0804
SL1524SB
Date : 13-11-2008
12
180°
B
Sblocco nuovo "B"
L
Sblocco nuovo "D"