Cardin SLX Série Mode D'emploi page 11

READING THESE INSTRUCTIONS
REMARKS CAREFULLY
ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
READING THESE IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING ORDER OF THE SYSTEM
AND CREATE DANGER SITUATIONS FOR THE USERS OF THE SYSTEM. SAVE THESE INSTRUCTIONS FOR FUTURE USE.
• These instructions are aimed at professionally qualified 'INSTALLERS
OF ELECTRICAL EQUIPMENT' and must respect the local standards
and regulations in force.
All materials used must be approved and must suit the environment in
which the installation is situated and all maintenance operations must
be carried out by professionally qualified technicians.
• This appliance must be used exclusively for the purpose for which it has
been made. 'i.e. for the automation of sliding gates' with a maximum
weight of up to 800 - 1000 - 1500 or 3000 kg.
Caution! The installation of both anti-derailment buffers
is absolutely obligatory.
Caution! The reversible model SLX1024REV requires
an electric lock to guarantee that the gate locks in the
closed position.
IMPORTANT SAFETY INSTRUCTIONS
• This appliance must never be used by people (including children) with physical,
sensory or mental disabilities or by people without specific knowledge and
experience in its operation unless they are able to benefit from the experience or
are being taught to use the appliance whilst being safeguarded by the presence of
somebody responsible for their safety.
• Before installing make sure that the guided parts are in good condition, correctly
balanced and that they open and close correctly.
• Avoid becoming trapped between the moving parts and the fixed parts during the
opening and closing movements.
• The motor's power cable must be made of polychloroprene in conformity with the
international standard 60245 IEC 57.
It is the responsibility of the installer to make sure that the following public safety
conditions are satisfied:
1) Ensure that the gate operating installation is far enough away from the main road
to eliminate possible traffic disruptions and that the size of the gate, the distance
from the road and the work cycle speed can in no way interfere, causing possible
traffic hazards.
2) The motor must be installed on the inside of the property and not on the public
side of the gate. The gates must not open onto a public area.
3) The sliding gate operator is designed for use on gates through which vehicles are
passing. The gates must not be fitted with pedestrian access doors.
4) The minimum controls which may be installed are OPEN-STOP-CLOSE, these
controls must be installed at a height between 1,5 and 1,8 m and in a location
not accessible to children. Controls installed externally must be protected by a
safety device inhibiting unauthorised use.
5) Do not allow children to play with the operator or with the control devices.
6) At least two warning signs should be placed, where
they can be easily seen by the public, in the area of the
system of automatic operation. One inside the property
and one on the public side of the installation. These signs
must be indelible and not hidden by any objects (such
as tree branches, decorative fencing etc.). Make sure that the end-user is aware
that children and/or pets must not be allowed to play within the area of a gate
installation. If possible include this in the warning signs
7) Ahead of the automation a means of disconnection from the power supply must
be installed which has an opening distance on the contacts of all the poles and
ensures that the power supply is completely cut off under the conditions of a
category III overvoltage situation.
8) A correct earth connection is fundamental in order to guarantee the electrical
safety of the machine.
9) If you have any questions about the safety of the gate operating system, do
not install the operator. Contact your dealer for assistance.
ATTENTION! IMPORTANT SAFETY INSTRUCTIONS
IS IMPORTANT
BEFORE PROCEEDING
AUTOMATIC OPENING
APERTURA AUTOMATICA
FERMETURE AUTOMATISÉE
AUTOMATISCHER ÖFFNUNG
Installation company: Serial number:
Product model:
Installation date:
®
Weight in kg:
riello elettronica group
FOR PERSONAL
WITH THE INSTALLATION.
IN THIS ORIGINAL INSTRUCTION MANUAL. NOT
TECHNICAL DESCRIPTION
- Mains power supply 230 Vac.
- Motor powered with a maximum voltage of 37 Vdc.
- Upper and lower cover in highly resistant shock-proof plastic.
- The reduction unit stator is made of die cast aluminium and contains a
never ending screw and double reduction lubricated with permanently
fluid grease.
- Irreversible reduction system with a key-operated manual release
mechanism.
- The incorporated electronic programmer contains the power stage, the
logic control, battery charger and the radio receiver decoding module. The
power supply is routed to the electronics card via a separate transformer
Q
which is housed in the same container and is connected to the card by
Faston clips.
- The system is fitted with electronic deceleration control which reduces
the stress caused by the gate inertia when it stops.
Accessories
Gear rack in nylon reinforced with glass fibre, 30 mm x 20 mm,
M4, 1 m pieces
CRENY1 Version with 4 lower fastening slits
For sliding gates up to 600 kg
CRENY Version with 6 upper fastening slits
For sliding gates up to 1500 kg
CREMP Version with 6 lower fastening slits
For sliding gates up to 1500 kg
Gear rack in galvanised steel for industrial installations.
SLOAC 22 mm x 22 mm to be soldered, 2 m pieces.
SLOAC2 30 mm x 12 mm with fastening slits, 1 m pieces.
USER INSTRUCTIONS
Attention! Only for EU customers - WEEE marking.
This symbol indicates that once the products life-span has
expired it must be disposed of separately from other rubbish. The
user is therefore obliged to either take the product to a suitable
differential collection site for electronic and electrical goods or
to send it back to the manufacturer if the intention is to replace
it with a new equivalent version of the same product.
Suitable differential collection, environmental friendly treatment and
disposal contributes to avoiding negative effects on the ambient and
consequently health as well as favouring the recycling of materials.
Illicitly disposing of this product by the owner is punishable by law and
will be dealt with according to the laws and standards of the individual
member nation.
During the opening/closing manoeuvre check for correct operation and
ZVE: 572 - Mod: 04-09-2017
activate the emergency stop button in case of danger.
Warning! Entrapment danger. When using the device you are advised to
wait for the gate to copmpletly open before crossing its threshold and to
pay the maximum attention in order to avoid becoming trapped between the
hinged parts and the fixed parts during the opening and closing movements.
During blackouts with a flat battery the gate can be released and manually
manoeuvred using the supplied release key (see manual release).
The appliance is not suitable for continuous operation and may only be
operated using a duty cycle of 70%.
11
SAFETY. READ THE
PAY PARTICULAR ATTENTION
FOLLOWING
TO