Control Network Malfunction; Safety Instructions Related To The Product And Technology; Scope Of Delivery; About This Product - Emerson AVENTICS PROFINET Notice D'instruction

• To avoid injuries due to unsuitable spare parts, only use accessories and spare
parts approved by the manufacturer.
• Comply with the technical data and ambient conditions listed in the product
documentation.
• If unsuitable products are installed or used in safety-relevant applications, this
may result in unintended system operating states that may lead to injuries
and/or equipment damage. Therefore, only use a product in safety-relevant
applications if such use is specifically stated and permitted in the product doc-
umentation.
• You may only commission the product if you have determined that the end
product (such as a machine or system) in which the AVENTICS products are in-
stalled meets the country-specific provisions, safety regulations, and stan-
dards for the specific application.
• Do not modify or convert the device.
• Only use the device within the performance range provided in the technical
data.
• Do not place any mechanical loads on the device under any circumstances. Do
not place any any objects on it.
• The warranty only applies when the product is used as intended.
• Observe the related safety notes in the operating instructions.
Transport and storage
• A problem-free and safe operation of the devices requires proper transport,
correct storage, installation and assembly.
During cleaning
• Only clean the device using a slightly damp cloth. Only use water and, if nec-
essary, a mild detergent.

2.6 Control network malfunction

Products with Ethernet connection are designed to be used on specific industrial
control networks. Observe the following safety measures:
• Always follow industry best practices for network segmentation.
• Avoid exposing products with Ethernet connection directly to the Internet.
• Minimize internet and business network exposure for all control system de-
vices and/or control systems.
• Ensure that products, control system devices and/or control systems are not
accessible from the Internet.
• Locate control networks and remote devices behind firewalls and isolate them
from the business network.
• If remote access is required, only use secure methods such as Virtual Private
Networks (VPNs).
NOTICE! Recognize that VPNs and other software-based products may have
vulnerabilities. A VPN is only as secure as the connected devices it serves. Al-
ways use the current version of the VPN, the firewall and other software-based
products.
• Ensure that the latest released software and firmware versions are installed on
all products connected to the network.

2.7 Safety instructions related to the product and technology

Prior to installation
• The bus coupler (electrostatically endangered components) may only be
opened by trained personnel.
• Make sure the relevant system component is without pressure or voltage be-
fore assembling or when connecting and disconnecting plugs. Protect the sys-
tem against being restarted.
• Only use a power pack with safe isolation in accordance with DIN EN 60742,
classification VDE 0551 for the supply voltage. Please pay attention to exter-
nal fuses that comply with this description.
• The warranty will not apply if the product is incorrectly assembled.
During assembly
• Always assemble the bus coupler on a mounting plate or in a control cabinet.
• Refer to the operating instructions.
• Lay the lines so that no one can trip over them.
• Other system parts may be damaged by uncontrolled device movements if it
has not been properly mounted. Make sure that the device is securely fas-
tened.
• Ground the devices according to national regulations.
AVENTICS™ PROFINET | R412013605-BAL-001-AD | English
• Only use cables indicated in the operating instructions or quotation drawings.
Commissioning
• Installation/assembly and commissioning of the device may only be carried
out in a voltage-free and pressure-free state by trained and qualified special-
ists.
• Only put the device into operation if it has been completely assembled, cor-
rectly wired and tested.
• Before connecting or disconnecting the plugs, switch off the operating volt-
age to prevent damage to the electrical system.
In operation
• Observe the related safety notes in the operating instructions.

3 Scope of delivery

• 1x bus coupler PROFINET DDL
• 1 set of operating instructions

4 About This Product

4.1 Performance specifications

The bus coupler is used to connect the DDL system to a PROFINET field bus.
The bus coupler communicates with the fieldbus system and monitors the DDL
(Drive and Diagnostic Link).
The bus coupler is designed only for use as a device on a PROFINET bus system.
The bus coupler is a modular I/O device that conforms to PROFINET specifica-
tions.
The bus coupler connects the local I/O devices with the PROFINET network. In the
data model, these I/O devices are modularly connected to the bus coupler.
The bus coupler functions as an interface between the PROFINET network and
the local DDL participants.

4.2 Product description

6
Fig. 1: Product overview
1 PROFINET LEDs
3 X7E1: PROFINET OUT
5 X1S: M12 power supply (integrated
X1S power supply plug)

4.3 Product identification

Observe the product information on the product and packaging.
1
5
2 X7E2: PROFINET IN
4 XPD: DDL connection
6 S1/S2
2
3
4
12