Cleaning - Scheppach HS111 Traduction Des Instructions D'origine

3. Firmly press the workpiece against the transverse
stop (9).
4. Switch on the extraction system and then the cir-
cular table saw.
5. To make the cut, slide the transverse stop (9) and
the workpiece in the direction of the saw blade (7).
11.4 Cutting narrow workpieces (fig. 23)
Be sure to use a push stick (22) when making longitu-
dinal cuts in workpieces smaller than 120 mm in width.
With short workpieces, use the push stick (22) from
the beginning.
1. Adjust the parallel stop (1) according to the work-
piece height and the desired width (see 10.4).
2. Place your hands flat on the workpiece with your
fingers closed and slide it along the parallel stop
(1) into the saw blade (7).
3. Always use the push stick (22) to push the work-
piece through to the end of the riving knife (6).
11.5 Cutting extremely narrow workpieces
(fig. 24)
Be sure to use a wooden push block (31) when mak-
ing longitudinal cuts in very narrow workpieces with a
width of 50 mm and less.
The wooden push block (31) is not included in the
scope of delivery! (Available from your specialist deal-
er) Replace the wooden push block (31) without delay
when it becomes worn.
During sawing, workpieces can become jammed
between the parallel stop (1) and the saw blade (7),
caught by the saw blade (7) and then ejected at
speed. For this reason, the lower guide surface of the
parallel stop (1) should be favoured (see fig. 16). Shift
the stop rail (1a) if required (see 10.4.2).
1. Adjust the parallel stop (1) according to the work-
piece height and the desired width (see 10.4).
2. Use the wooden push block (31) to press the
workpiece against the stop rail (1a) and use the
push stick (22) to push the workpiece through to
the end of the riving knife (6).
11.6 Cutting chipboard
To prevent the cut edges from breaking off when cut-
ting chipboard, proceed as follows:
The saw blade (7) should not be set higher than 5 mm
above the workpiece thickness (see also 10.2).
11.7 After sawing
1. Switch off the circular table saw first and then the
extraction system. The saw blade continues to run
for a longer time.
2. Disconnect the circular table saw from the mains
by pulling the mains plug out of the power socket.
3. Do not remove the cut waste on the saw table until
the saw blade has returned to its resting position.
4. Allow the circular table saw to cool down com-
pletely.
11.8 Removing jammed material
m WARNING
Danger of injury for fingers and hands due to sharp
edges
- Wear protective gloves.
• Switch off the circular table saw immediately and
disconnect the mains plug from the power socket if
the saw blade is jammed in the workpiece or other
blockages occur.
• Use protective gloves and do not touch the saw
blade with your bare hands.

12. Cleaning

m DANGER
Risk of electric shock due to water entering into the
machine.
- Do not splash the product with water.
m WARNING
Danger of injury due to unexpected start-up of the ma-
chine
- Pull the mains plug out of the outlet.
12.1 Cleaning the product and saw blade guard
ATTENTION
Product damage due to insufficient cleaning
- Clean the product thoroughly after each use.
ATTENTION
Product damage due to aggressive solvents or clean-
ing agents.
- Use a brush to remove course dirt.
- Clean the product with a damp, clean, lint-free
cloth and soft soap.
1. Remove dust and chips with a brush after each
working operation.
2. Clean the ventilation holes with a lint-free cloth.
12.2 Clean the product with compressed air
ATTENTION
Product damage due to use of a compressed air de-
vice with too high of a pressure
By cleaning the product with highly compressed air,
electrical components may become damaged.
- Use a compressed air device with a low pressure
of max. 2 bar.
1. Always keep enough distance to the product.
2. Remove dirt with a compressed air device (max.
2 bar).
www.scheppach.com
GB | 41