UFESA AS3016E Mode D'emploi page 9

– wooden floors, plastic floors, ceramic tiles etc. pull out
the brush by pressing the switch on the combination
brush according to the figure
when vacuuming carpets (set the switch in "
7
Pull the plug and cord (3) out of the vacuum cleaner.
While pulling out the cord, pay attention
to the yellow stripe which signals the
end of the cord. Further attempts (pulling
on cord) may result in damaging the cord.
8
Plug in the appliance.
Before turning the vacuum cleaner on, check whether
the "CYKLON" dust container is installed in the chamber
of the vacuum cleaner, and whether the inlet and outlet
filters are installed in the vacuum cleaner.
9
Switch on the vacuum cleaner by pressing the "on/
off" button (7).
10
The vacuum cleaner is equipped with a suction
power regulation control. The power is controlled by
means of a knob.
11
Turning the knob according to the label increases
or respectively decreases the suction power.
Filter disassembly
Before changing the filters make sure that the vacuum
cleaner is switched off and unplugged from the mains
supply.
INLET FILTER CONE
It is necessary to clean the inlet filter cone from time
to time.
1
Remove the "CYKLON" dust container and empty it
according to paragraph
2
Release the fastening of the EPA basic filter (14)
and remove it from the "CYKLON" dust container.
3
Press the button situated on the "CYKLON" dust
container and open the bottom of the container.
4
Turn the inlet filter cone (17) clockwise.
5
Remove the inlet filter cone from the "CYKLON"
dust container.
6
If the inlet filter cone (17) is dirty, it may be rinsed
with running water. Remember to dry the cone before
its reinstallation.
Pay attention to the gasket placed on the
bottom of the cone collar. Do not lose it.
. Retract the brush
F
.
7
Place a new/rinsed inlet filter cone into the socket
in such a way that the two protrusions placed on the
collar are situated under the fastening in the body of
").
the container.
8
The cone should be pressed tightly and turned to
the limit counterclockwise. A characteristic click notifies
about a proper installation.
9
Snap the bottom of the "CYKLON" dust container.
10
Place the EPA basic filter (14). Pay attention so
that the two protrusions on the bottom part of the EPA
basic filter (14) find their way into the holes of the dust
container.
11
Place the "CYKLON" dust container in the chamber
of the vacuum cleaner. A characteristic click notifies
about a proper installation.
BASIC EPA FILTER & FOAM FILTER
It is necessary to clean the basic EPA filter from time to
time, as it is contaminated with dust.
● Uninstall the "CYKLON" dust container and empty it
according to paragraph
1
Release the fastening of the EPA basic filter (14)
and remove it from the "CYKLON" dust container.
2
Remove the foam filter (15). If the foam filter
(15) is dirty, it may be washed with running water.
Remember to dry it off before reinstalling the filter.
The main function of the foam filter (15) is protecting
the basic EPA filter (14) from excessive dirt.
Due to safety reasons it is forbidden to
install a wet or damaged foam filter (15).
C
● Clean the pleads of the basic EPA filter (14), if any
of them are damaged, the filter definitely must be
replaced. If the basic EPA filter (14) is dirty, it may be
washed with running water. Remember to dry it off
before reinstalling the filter.
Due to safety reasons it is forbidden to
install a wet or damaged basic EPA
filter (14).
● Place the foam filter back into its place.
3
Put the new/rinsed EPA basic filter (14) back in its
place – pay attention to put the two protrusions in the
bottom part of the EPA basic filter (14) in the holes of
the dust container. A characteristic click notifies about
a proper installation.
4
Place the "CYKLON" dust container with the installed
basic EPA filter (14) in the chamber of the vacuum cleaner.
A characteristic click notifies about a proper installation.
F
.
D