Analog way OCTO-PLUS Manuel Utilisateur page 36

Chapter 9 : REMOTE CONTROL PROGRAMMER'S GUIDE (continued)
9-4. COMMANDS AND RESPONSES TABLE (continued)
ASCII RESPONSE
COMMAND
FRAME & LOGOS COMMANDS (OCTO-LOGO
PC PCH
** LM LMOD
** LI LIND
** LP LPLG
** LC LCUR
** LE LEMP
** Lh LHPO
** Lv LVPO
** LH LHSZ
** LV LVSZ
** LL LLEV
** Lb LBKC
** LS LSTO
** Lo LOFM
** LA LABT
** Lt LSTY
** Ls LSTA
** Lp LPIX
** Ll LLIN
** Ld LLD
** LD LDYS
NOTE: To store a logo you should:
Select the logo recording mode with the LM command (1LM).
Adjust the position and size of the logo area with the Lh, Lv, LH and LV commands.
Adjust the luma key level (with LL command) and the background color (with Lb command).
Select a logo memory with the LC command.
Make a store with LS command (1LS).
To store a frame you should:
Select the frame recording mode with the LM command (2LM).
Make a store with the LS command (1LS).
NOTE: To assign a logo/frame to an input you should:
Select the assignment mode with the LM command (0LM).
Select the input with the PC command.
Select an index (1 or 2) with the LI command.
Select a stored logo/frame with LP command.
Adjust the horizontal & vertical position of the logo with the Lh & Lv commands.
NOTE: * = command available on the OCTO-FADE
** = command available on the OCTO-LOGO
PAGE 36
COMMAND
DESCRIPTION
™
Input selection for adjustment.
Frame/logo mode.
Index selection (according to PCH) .
Logo & frame assignment (according to
PCH & LIND. And LMOD = 0).
• In use mode: Logo/frame in using
process.
• In logo recording mode: Number of
the logo to be store (always >1).
• In frame recording mode: Number of
the frame to be store (always = 1).
• In erase mode: number of the logo to
be erase (0 = erase all).
Status of the frame/logo memories
(according to LCUR).
Horizontal position of the logo area.
Vertical position of the logo area.
Horizontal size of the logo area.
Vertical size of the logo area.
Luma key level.
Background color.
• In recording mode: frame/logo storing.
• In erase mode: frame/logo erasing.
Output format during the logo storing.
Stop the frame storing.
Frame/logo type.
Status of the logo programmer
Pixels number in a line of the logo area. Rd
Lines number in a logo area.
Fade logo duration (0.02 second step).
Display logo (according to PCH)
TYPE
MIN MAX
™
& OCTO-FX only)
Rd/Wr 0
Rd/Wr 0
Rd/Wr 0
Rd/Wr 0
Rd/Wr 0
Rd 0
Rd/Wr 0 255
Rd/Wr 0 255
Rd/Wr 5 255 5 = 3%
Rd/Wr 5 255 5 = 3%
Rd/Wr 0 255
Rd/Wr 0
0
Rd
0
Rd
Rd/Wr 0
Rd 0
0
Rd
0 65535
Rd 0 65535
Rd/Wr 15 255 15 = 0.3 second
Rd/Wr 0
™ ™
& OCTO-FX only.
™ ™
& OCTO-FX only.
VALUE
DESCRIPTION
0 = All inputs
8
2 = INPUT #2................ 8 = INPUT #8
0 = use & assignment mode.
1 = logo recording mode.
4 2 = frame recording mode.
3 = auto list mode (display all logo parameters).
4 = erasing mode.
1 0 = index 1
0 = none
1
2 = logo 1...................
0 = no logo
1 = frame
2 = logo 1
3 = logo 2
9
4 = logo 3
5 = logo 4
....
9 = logo 8
0 = logo/frame memorized.
1
1 = empty memory.
7
1 1 = STORE or ERASE (automatic reset).
11 Identical as F command.
1 1 = stop the frame storing (automatic reset).
1 0 = frame
0 = free.
1 = logo/frame in recalling process.
2 = logo/frame in storing process.
5
3 = output format incompatible with the logo.
4 = logo/frame in consulting process.
5 = logo/frame in erasing process.
These 2 commands allow to calculate the
duration of the storing.
1 0 = Display OFF
Rd = Read only command.
Rd/Wr = Read and write command.
OCTO range
1 = INPUT #1
1 = index 2
1 = frame
9 = logo 8
255 = 100%
255 = 100%
1 = logo
255 = 5.1 seconds
1 = Display ON