Analog way OCTO-PLUS Manuel Utilisateur page 34

Chapter 9 : REMOTE CONTROL PROGRAMMER'S GUIDE (continued)
9-4. COMMANDS AND RESPONSES TABLE
The following table resumes commands that are recognized as valid and the responses that will be returned to the control
device (on RS-232 port).
ASCII RESPONSE
COMMAND
FRONT PANEL COMMANDS
C CH
c ch
o OBLK
G TAKE
Z FRZ
*
tE EFFO
INPUT COMMANDS
PC PCH
PE PEN
PL PLD
PR PRGB
PI PSTD
PP PPRC
OUTPUT COMMANDS
F OFMT
fm OSYN
fs SCRN
p OPAT
mH MHPO
mV MVPO
mW MHSZ
mS MVSZ
NOTE: * = command available on the OCTO-FADE
** = command available on the OCTO-LOGO
PAGE 34
COMMAND
DESCRIPTION
Selected input.
Input selection.
Black screen selection.
Transition status.
FREEZE.
Effect selection.
Input selection for adjustment.
Input disabling (according to PCH).
H sync load selection (according PCH) Rd/Wr
Input signal type selection. (according
to PCH).
Input standard selection (according to
PCH).
VCR mode (according to PCH).
Output format selection.
Output sync selection.
Type of screen selection
Test pattern.
Centering pattern: horizontal position. Rd/Wr
Centering pattern: vertical position.
Centering pattern: horizontal size.
Centering pattern: vertical size.
TYPE
MIN MAX
Rd 1
Rd/Wr 1
Rd/Wr 0
Rd 0
Rd/Wr 0
Rd/Wr 0
Rd/Wr 0
Rd/Wr 0
0
Rd/Wr 0
Rd/Wr 0
Rd/Wr 0
Rd/Wr 0 12
Rd/Wr 0
Rd/Wr 0
Rd/Wr 0
0 255
Rd/Wr 0 63
Rd/Wr 0 255
Rd/Wr 0 63
™ ™
& OCTO-FX only.
™ ™
& OCTO-FX only.
VALUE
DESCRIPTION
1 = INPUT #1
8
3 = INPUT #3
5 = INPUT #5
8
7 = INPUT #7
1 = black screen
1
1 = transition in process (automatic reset at
1
the end of the effect transition).
0 = inactive
1
0 = CUT 1 = FADE
2
0 = All inputs
2 = INPUT #2
8 4 = INPUT #4
6 = INPUT #6
8 = INPUT #8
0 = Input disable
1
0 = Hi-Z load
1
0 = SDTV Composite 1 = SDTV S.VIDEO
2 = SDTV YUV
9 4 = SDTV RGsB
6 = Computer (SOG) 7 = Computer H&V/C
8 = HDTV
0 = NTSC / PAL / SECAM
1 = NTSC
6
3 = NTSC 4.43 60Hz 4 = PAL 4.43 60 Hz
5 = SECAM
0 = OFF
1
If fast switching =
internal rate
0 = VGA 60 Hz
1 = SVGA 60 Hz
2 = XGA 60 Hz
3 = SXGA 60 Hz
4 = SXGA+ 60Hz
5 = VGA 75 Hz
6 = SVGA 75 Hz
7 = XGA 75 Hz
8 = SXGA 75 Hz
9 = D-ILA 4/3
10 = D-ILA 16/9
11 = HDTV 480p
12 = HDTV 720p
0 = H &V
2
2 = SOG (Sync On Green).
0 = screen 4/3
1
0 = no pattern
2
2 = color bar
Rd = Read only command.
Rd/Wr = Read and write command.
OCTO range
2 = INPUT #2
4 = INPUT #4
6 = INPUT #6
8 = INPUT #8
1 = active.
2 = TITLE
1 = INPUT #1
3 = INPUT #3
5 = INPUT #5
7 = INPUT #7
1 = Input enable
1 = 75Ω load
3 = SDTV RGBS TTL
5 = SDTV RGBS ana.
9 = Audio only
2 = PAL
6 = Black & White
1 = ON
input # X
0 = 640x480L
1 = 800x600L
2 = 1024x768L
3 = 1280x1024L
4 = 1400 x1050 L.
5 = 640x480L
6 = 800x600L
7 = 1024x768L
8 = 1280x1024L
9 = 1365x1024L
10 = 1365x768L
11 = HDTV 480p
12 = HDTV 720p.
1 = Composite
1 = screen 16/9
1 = centering