Publicité
Les langues disponibles
Les langues disponibles
tion with your electric power company if necessary,
that the connection point at which you wish to oper-
ate the product meets one of the two requirements,
a) or b), named above.
Damaged electrical connection cable.
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Pressure points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Ensure that the connection cables are dis-
connected from electrical power when checking for
damage.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the designation "H05VV-F".
The printing of the type designation on the connec-
tion cable is mandatory.
AC motor:
• The mains voltage must be 220 - 240 V~.
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
• When using extension leads, make sure that they
are suitable for outdoor use and that they have a
sufficient wire cross-section:
1-10 m: 1.5 mm
2
10-30 m: 2.5 mm
.
2
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Data of motor type plate
10. Operation
The machine consists of an assembly with a pump,
which is covered by a shockproof housing. The ma-
chine is equipped with a lance and a handy pistol for
an optimal working position, whose shape and equip-
ment comply with the applicable regulations.
Commissioning:
Once you have completely assembled the high-pres-
sure cleaner and all connections have been made,
proceed as follows:
Turn on the water supply. Unlock the pistol (16) via
the locking switch (C). Pull back the trigger lever (D)
so that the air in the device can discharge. (Fig. 8)
Switch on the device by setting the on/off switch (5)
to "ON". Next, press the trigger lever (D). (Fig. 1/8)
To switch off, release the trigger lever (D), and the
device switches to stand-by. The high-pressure
cleaner starts again when you press the trigger le-
ver (D). (Fig. 8)
To switch off the high-pressure cleaner completely,
set the on/off switch (5) to "OFF". (Fig. 1)
Cleaning agent container (8)
Fill the cleaner container with the corresponding
cleaner. The cleaner is dosed automatically in low-
pressure operation.
Cleaning agents are only suctioned if the extension
piece (15) is fitted.
Using the attachments (Fig. 1 / 8)
• Turbo nozzle (14): For eliminating stubborn dirt.
• Nozzle (13): For coarse cleaning work. The water
jet can be adjusted by turning the nozzle.
11. Transport
m CAUTION
Risk of injury and damage!
Pay attention to the weight of the device when trans-
porting and storing. Always lift and carry the device
by the handle.
Secure the device against slipping and toppling.
Stow the accessories accordingly on the device.
12. Storage
Store the device and its accessories in a dark, dry and
frost-free place that is inaccessible to children. The op-
timum storage temperature lies between 5 and 30 ˚C.
Store the power tool in its original packaging.
Cover the power tool to protect it from dust or mois-
ture. Store the operating manual with the power tool.
www.scheppach.com
GB | 23
Publicité
Chapitres
